Setting up a 8lb paxton

289 · 08-24-2006, 11:14 PM

Can anyone please tell me what I might need for a 8lb blower setup.
I have a 30#injector FMU and 24#FMU. I also have an adj fuel reg and a 155lp intank fuel pump. But stock 19#injectors
I will be running a 50 shot wet system at the same time.
Do I need a new MAF and injectors and a 225LPH intank.
Thanks

meknized · 08-27-2006, 09:49 PM

Hey,

for a blower and N2o set up it is imperative to have everything matched and in good shape. I would definitely use the 255 LPH pump and with both power adders I would at the very minimum use #30lb injectors. I would also make sure that the FMU is matched to the injectors to be sure you have the correct rate of gain. Some I know don't even bother with the FMU and go straight to electronic tuning with a wide band O2 sensor and hand held tuner. Of course have the best MAF matched to the injectors.

08-24-2006, 11:14 PM	#1
289 Registered Member Join Date: Jan 2000 Location: Mount Joy, PA , U.S. Posts: 198	Setting up a 8lb paxton Can anyone please tell me what I might need for a 8lb blower setup. I have a 30#injector FMU and 24#FMU. I also have an adj fuel reg and a 155lp intank fuel pump. But stock 19#injectors I will be running a 50 shot wet system at the same time. Do I need a new MAF and injectors and a 225LPH intank. Thanks

08-27-2006, 09:49 PM	#2
meknized fox fanatic Join Date: Jul 2004 Location: wichita Ks. Posts: 61	Re: Setting up a 8lb paxton Hey, for a blower and N2o set up it is imperative to have everything matched and in good shape. I would definitely use the 255 LPH pump and with both power adders I would at the very minimum use #30lb injectors. I would also make sure that the FMU is matched to the injectors to be sure you have the correct rate of gain. Some I know don't even bother with the FMU and go straight to electronic tuning with a wide band O2 sensor and hand held tuner. Of course have the best MAF matched to the injectors. __________________ meknized Blue/silver 89 GT, Coast 331, ported GT-40x heads, X cam, cobra intake, 70mm TB, 75mm bullet, mac intake, 24lb inj, 255 lph fuel pump, accufab regulator, pulleys, MSD coil, 6AL, 300+ wires, Tremec 5 spd. pro 5.0 shifter, FMS drive shaft, headers, X-pipe, flowmasters, auburn pro series posi. moser 31s axles,3:73s, etc. Best ET 12.02@112.5 a pic A vid of a run:http://www.youtube.com/watch?v=l9JMcErxML8

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
SN-92,SN-93,GSS Paxton Ball-Drive Guys Step INSIDE	Mustanguy	Windsor Power	4	02-13-2006 12:13 PM
Point Gap Setting 72 Mustang 6 cylinder	vavs	Classic Mustangs	5	07-30-2005 07:47 PM
HELP: Problems after Paxton Novi 1000 install	Meatman	Windsor Power	3	10-17-2002 06:03 PM
Paxton SC	StreetStang37	Windsor Power	7	06-18-2001 06:12 PM
Paxton Supercharger	darkstarjj	Windsor Power	0	04-02-2001 09:33 PM