![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: May 2001
Location: Sour Lake, TX
Posts: 211
|
![]() I am wondering if anyone running the Victor 5.0 EFI intake are having any heat problems. Since the intake does'nt have a water transfer port at the back of the intake. The new 347 we put in our car runs hot doing any idling. I have all the good cooling stuff and it just keeps on climbing. Runs just fine on the road and under hard accel conditions. Just pegs out if idled. Thanks.
|
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Sep 1998
Location: IL
Posts: 1,155
|
![]() I doubt it has anything to do with the Victor 5.0 manifold. SBF intakes don't have or need a water crossover in the back. Look at a stock or Cobra intake.
Coolant flows from the water pump through the block (down both cylinder banks front to back, then up and through the heads (back to front), then into the manifold's front crossover and out the thermostat to the radiator. That's why when you install the head gaskets it's imperative that they are installed correctly with the water passages in back open and in the front blocked off. Sounds like you don't have enough air flow through the radiator at idle. Stock mechanical fan? Shroud? Underdrive pulleys? Electric fan? ------------------ Craig Supercharged 93 GT Basically stock 93 Cobra "I drive way too fast to worry about cholesterol!" |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: May 2001
Location: Sour Lake, TX
Posts: 211
|
![]() Im running with the stock shroud, revised police ford fan and clutch. Edelbrock victor water pump, new aluminum 3 core rad. New stant 180 thermostat with new 16lb cap.
|
![]() |
![]() |
![]() |
#4 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() I was having heat problems with my 347..I put in a electrical fan in front of the radiator for stop and go driving..That took care of most of my heating probs..
------------------ 347 Stroker Motor: Balanced, Cobra Transmission, Extrude Ported and Polished Upper and ported Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, 30lb Bosch Injectors, Holley AFPR, March Underdrive Pulleys, Perma-Cool Fan, 3-Core Radiator, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 73mm Vortech MAF, 70mm TB, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, AC and Smog del, rear seat del. |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Apr 1999
Location: Hayes, Va, USA
Posts: 798
|
![]() Did you have to mill the intake and port your heads to accept the Vic 5.0?
I've got AFR 185cc heads and stopped down at the engine shop the other day. The builder shined a flashlight down into the runners. It was interesting to say the least. The heads had a set of 1262 gaskets on them and I could see the silicon bead along the roof of the intake. So the lower needs to be milled about 80 thousandths and the roof of the intake runner needs to be squared off and blended back into the port |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Jul 2001
Location: Refugio
Posts: 67
|
![]() hey i have a question..will a fan on front and back (both electric) of the radiator work?
|
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: May 2001
Location: SOUR LAKE,TX (U.S.A.)
Posts: 64
|
![]() Nope. Did'nt have any fit probs. But I'm using Edelbrock heads.I would double check that before you let anyone cut on your stuff.
|
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Jun 2000
Location: sanantonio, Tx, usa
Posts: 1,407
|
![]() Well the police fan is crap, it's a power robbing piece of junk, mine broke while i was going 40 mph, and cost me a radiator, i got a blacmagic fan, run cooler, and knocked of a good amount of time on e.t.'s.
|
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: May 2001
Location: SOUR LAKE,TX (U.S.A.)
Posts: 64
|
![]() WHERE DID IT BREAK AT? HOW LONG DID YOU HAVE IT ON THERE?
|
![]() |
![]() |
![]() |
#10 | |
Registered Member
Join Date: Apr 1999
Location: Hayes, Va, USA
Posts: 798
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Intake selection with a 383/408 stroker | Capri306 | Windsor Power | 12 | 05-03-2002 10:12 PM |
Explore intake??????????? | William Bowers | Windsor Power | 2 | 02-14-2002 10:27 PM |
HELP!!! oil in intake, what to do?? | bosco | Windsor Power | 4 | 02-03-2002 05:02 PM |
OIL IN INTAKE almost sure from 'pcv' | QUIN | Windsor Power | 8 | 03-09-2001 01:58 PM |
Is the true about Edelbrock heads with TFS intake? | gt93mustang | Windsor Power | 14 | 03-06-2001 07:01 PM |