come on guys, someone has got to know something about my tranny!!!

phil bacchi · 10-03-2002, 05:24 AM

hey there. im trying to get a 460 stroker wedged into a 91 lx mustang. i have a c6 tranny that bolts up to a 460 block. im trying to put this thing in my stang. this tranny has a flat flange that you bolt the driveshaft up to. i think its from a truck. my questions are these:

do i have to change the output shaft if i change the tailshaft to accept the splined driveshaft yoke that i need for my stang?

did ford make a c6 that is compatible with a 91 mustangs speedo cable, and what do i need to do to get my cable hooked up to my tranny?

should i even try to use this tranny, or should i find one from a 460 car?

pleeeeaaaase help me! i need all the info i can get here!!!!!

thanks!

Superpromustang · 10-03-2002, 09:35 AM

You need to get a different output shaft cover, I had this same problem when I was putting a c-6 in my 65 Ford truck, because the factory driveshaft was a two piece unit with the carrier bearing, so I had to change from the flat flange type to the spline type, so I could run a one piece drive shaft. As far as the speedo cable goes, all you should need is a speedo gear for a c-6 tranny, and it should bolt up to your factory speedo cable, if not, you'll need to get a different cable for that transmission, hope this helps you,

Kenny

10-03-2002, 05:24 AM	#1
phil bacchi Registered Member Join Date: Sep 2002 Location: indiana Posts: 2	come on guys, someone has got to know something about my tranny!!! hey there. im trying to get a 460 stroker wedged into a 91 lx mustang. i have a c6 tranny that bolts up to a 460 block. im trying to put this thing in my stang. this tranny has a flat flange that you bolt the driveshaft up to. i think its from a truck. my questions are these: do i have to change the output shaft if i change the tailshaft to accept the splined driveshaft yoke that i need for my stang? did ford make a c6 that is compatible with a 91 mustangs speedo cable, and what do i need to do to get my cable hooked up to my tranny? should i even try to use this tranny, or should i find one from a 460 car? pleeeeaaaase help me! i need all the info i can get here!!!!! thanks! __________________ sorry, i am not smart enough to know how to get one of these!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Tranny kickdown cable	Midnite Wrider	Classic Mustangs	16	05-03-2005 10:20 PM
Tranny won't shift! (long)	byrnech	Windsor Power	4	08-26-2002 10:50 AM
M5OD Tranny help needed	bigred90gt	Built Ford Tough	2	08-10-2002 04:48 PM
Auto Tranny in 2000 V6	Bake	Small Ponies	2	07-30-2002 01:53 PM
Tranny time	Dave_mustang_50	Windsor Power	4	01-25-2001 08:06 AM

10-03-2002, 09:35 AM	#2
Superpromustang Registered Member Join Date: Oct 2002 Location: Carthage, MO Posts: 59	You need to get a different output shaft cover, I had this same problem when I was putting a c-6 in my 65 Ford truck, because the factory driveshaft was a two piece unit with the carrier bearing, so I had to change from the flat flange type to the spline type, so I could run a one piece drive shaft. As far as the speedo cable goes, all you should need is a speedo gear for a c-6 tranny, and it should bolt up to your factory speedo cable, if not, you'll need to get a different cable for that transmission, hope this helps you, Kenny