© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
11-16-2002, 05:59 PM | #1 |
Registered Member
Join Date: Sep 2000
Location: rock hill,S.C. 29730
Posts: 420
|
Question about removing smog equipment
Concerning removal of tubes on back of heads ,I read that you can get plugs for the holes? Can you remove and plug them with the heads on the car? What else are are the attached to?
Thanks!!
__________________
88 GT: subs,pullies, 1 3/4 longtubes, flowmasters, AFR 165's,T,F #1 cam,Thyphoon intake, 24# inj., 73mm C&L,65mmT.B., 190LPH pump, Eagle sir rods, forged pistons in a newly rebuilt 306. DYNO TUNED TO 300.97 RWHP 337RWTQ |
11-17-2002, 04:56 AM | #2 |
Registered Member
Join Date: Mar 1999
Location: Amarillo, Texas, USA
Posts: 780
|
I think you would have to be real limber to do it while on the car. Not saying it can't be done, but my fat old fingers ain't goin there.
__________________
1986 four-eyed LX coupe, 358 Cleveland, Tremec TKO600/centerforce clutch, dish cut Probe forged pistons, comp cams hyd.roller cam, .579/.588@224/230, Edel.performer, 670 holley street avenger, CPR custom built long tubes, ported and polished 4bbl heads, manley valves, beehive springs, MSD peo-billet dist/MSD6AL, fluidamper, 5 lug conv. with 17x8 bullits there's more but it's still not finished yet. Oh, and the oldest boy is turning his 89 GT into a FFR cobra this next summer. |
11-17-2002, 05:25 AM | #3 |
Factoy Five Roadster
Join Date: May 2000
Location: Sevier Co,Tennessee
Posts: 1,681
|
The dealer has the plugs, but they screw in with a wide flat head screwdriver. Thats a problem. I used two bolts instead, as to have something to wrench on. I don't remember what size they were, but they were big. Maybe go to the dealer and measure them up for a bolt. Oh yeah,(Hole being plugged is threaded.) And the bolts only need be as long as the plugs, maybe 1/2 long or so.
The tubes may be secured to something else, like a trans bolt. Nothing else important back there. my $.02
__________________
Frank |
11-17-2002, 09:24 AM | #4 |
Registered Member
Join Date: Mar 2000
Location: Springfield, Ma, usa
Posts: 706
|
Sure you can plug the holes while the heads are on the car. You might have to remove a few other things though. You will need a 5/8" thread, 1" long bolt or plug. I used plugs that needed an allen wrench to install, from the hardware store. Its cleaner then a regular bolt and cheaper then going to a dealer for the plugs. Are you running an off road h-pipe? Cause if your not, removal of the smog pump and system will clog the cats from the lack of air flow the smog pump generates.
I did what your talking about doing this past summer. Heres a pic and you can see that it cleans up the engine bay a little bit.
__________________
NewEngland Auto www.baystategearheads.com -91 Mustang Coupe, ex 4cyl (sold) -99 F150, 3" lift, 35" Procomps, Magnaflow exhaust Last edited by HiFlow5 0; 11-17-2002 at 09:35 AM.. |
11-17-2002, 03:19 PM | #5 |
Moderator
Join Date: Mar 2001
Location: Myrtle Beach SC
Posts: 1,643
|
On all my cars, I just took a piece of 1x1/8 metal about two inches long, drilled a hole in it. and bolted it to the back of the head, There is 7/16 threaded hole right beside the smog holes that works well for the bolt and then the metal bar jsut covers the hole. Just be sure to use good high temp RTV sealant on it nad you'll be fine. And its alot easier to do it that way than to try and get a screw driver up there with the other plugs.
Bradley
__________________
1990 GT, 347, TFS TW Heads, TFS Cam, TFS Track heat, Twin turbos, FMIC, T5. Built Ford Tough Moderator |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
smog question!!! | Notchback5.0L | Windsor Power | 0 | 06-03-2003 06:51 PM |
Whats all involved in removing the smog pump from a 91 gt? | 4.6l-eatr | Windsor Power | 4 | 02-20-2002 09:11 PM |
Removing Smog Pump make much HP Diff? | ALS85GT | Windsor Power | 4 | 01-22-2002 04:12 PM |
Smog Pump Question | 93GTDIN | Windsor Power | 3 | 10-07-2001 08:23 AM |
Removing smog will do what? | KrashedMy5.0 | Windsor Power | 3 | 07-23-2001 10:15 PM |