![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() Well for some reason I switched from quaker state senthetic blend 10W30 to conventional valvoline 10W30. before it would use about 3/4 of a quart between oil changes and now i've used about 1.5 quarts in less than 2000 miles, so i know its the oil im using thats making it use a litte more but my question is what brand/senthetic?/blend?/conventional?/weight? oil should i be using with this motor? its got just over 100k on it now, also, i've heard good things about that Restore stuff for piston rings, has anyone here tried it? thanks guys
------------------ 88 Notch, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframe connectors, 65mm TB, shift kit, March ram air ,MSD coil, U/L control arms, 155lph fuel pump, cheap 2800 stall, Crane Adj.FPR, best 1/4--> 13.77@101.35 |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Oct 1999
Location: Cincinnati, Ohio
Posts: 1,575
|
![]() I've run quit a few different oils in my car, and I also work for a oil changing place. From my expirence Kendall 20w50 worked best for me. It didn't leak as much and the valvetrain was alot quieter then before.
------------------ 87 GT, 4 inch cowl hood,17x9 Cobra R's/255/45's,GT-40 heads,Crane 2031, Edelbrock intake, long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's. Best time 12.759 Best MPH 106.79 Best 60' 1.695 Visit my site at: http://www.geocities.com/cobrar93_2000/MyPage.html |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Jun 2001
Location: Conway, Ar, USA
Posts: 9
|
![]() I know when you use synthetic oil, you need to flush out your motor, before putting conventional back in it. THe synthetic and regular oil mix and make some kind of pasty stuff that hurts your motor. You may want to check into that. I'm not sure if it is the same with a synthetic blend oil, but it's worth checking out. Hope that was some help.
|
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Aug 2000
Location: Thousand Oaks, CA
Posts: 396
|
![]() I have never heard that about mixing synthetic and regular and getting some kind of pasty crap. Most bottles even say "Compatible with conventional motor oils". Anybody ever heard this?
|
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Jan 2001
Location: nashville, tn
Posts: 72
|
![]() I've never heard of that either. If it were true, I don't see how they could sell a synthetic BLEND, which is just that: A blend of synthetic and conventional motor oils.
------------------ 93 Coupe, long tubes, pro chamber, flowmasters, 3.73, auburn, alum driveshft, subframes, tri-ax, pulley, 73mm MAF, cobra Rs. |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Jan 2001
Location: nashville, tn
Posts: 72
|
![]() I've never heard of that either. If it were true, I don't see how they could sell a synthetic BLEND, which is just that: A blend of synthetic and conventional motor oils. To add to this.. I hear people talk about puoring ATF in the engine to clean it out. Whats up with that? Could someone elaborate?
------------------ 93 Coupe, long tubes, pro chamber, flowmasters, 3.73, auburn, alum driveshft, subframes, tri-ax, pulley, 73mm MAF, cobra Rs. |
![]() |
![]() |
![]() |
#7 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() anyone have any suggestions on which oil and weight to use?
------------------ 88 Notch, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframe connectors, 65mm TB, shift kit, March ram air ,MSD coil, U/L control arms, 155lph fuel pump, cheap 2800 stall, Crane Adj.FPR, best 1/4--> 13.77@101.35 |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
eibach advice needed | mustardjohn | Small Ponies | 6 | 08-19-2012 08:12 PM |
Eibach advice | mustardjohn | Corner Carvers Delight | 5 | 03-17-2004 10:03 PM |
Advice on injectors...PKRWUD I'd like your advice on this one as well | silver_pilate | Windsor Power | 3 | 06-09-2003 08:59 AM |
Guitarists, I need your quick advice. | Fox Body | Blue Oval Lounge | 8 | 10-12-2001 08:57 AM |