© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
01-24-2005, 01:19 PM | #1 |
Registered Member
Join Date: Jun 2001
Location: butler pa
Posts: 303
|
throwout bearing retainer?
i just got a new throwout bearing retainer in the mail and when i put it beside the one i just took off it is shorter is the factory aluminum shaft tbr longer than the aftermarket steel ones or did i get the wrong one thanks in advance for any help
__________________
92lx wannabe saleen |
01-26-2005, 01:33 PM | #2 |
Registered Member
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
|
Re: throwout bearing retainer?
Not sure here, my replacement ($15.99) from AutoZone was the same size. Just added some extra grease to it.
__________________
|
01-26-2005, 09:31 PM | #3 | |
Domestic Rice really sucks!
Join Date: Apr 2002
Location: KY
Posts: 973
|
Re: throwout bearing retainer?
Quote:
I have never seen/heard of this problem before. How much shorter is the steel one than the aluminum one? If it's just like an 1/8" I'd say you're alright.
__________________
The sig says it all. |
|
01-26-2005, 10:25 PM | #4 |
Registered Member
Join Date: Jun 2001
Location: butler pa
Posts: 303
|
Re: throwout bearing retainer?
the shaft on the unit that is on the tranny is 3 and 5/8 the new one is 3 inches other than that they look the same the new one is a ford racing steel unit instead of the aluminum one and it was $40
__________________
92lx wannabe saleen |
01-27-2005, 11:08 AM | #5 |
Registered Member
Join Date: Jun 2001
Location: butler pa
Posts: 303
|
Re: throwout bearing retainer?
ok i feel stupid the shafts are diff lengths if you measure them from the housing but apon futher ins (and a phone call to the supplier) i now see that the overall length is the same because the housing extendeds further up the shaft on the steel unit then it does on the oe aluminum unit
__________________
92lx wannabe saleen |
01-27-2005, 09:59 PM | #6 |
Domestic Rice really sucks!
Join Date: Apr 2002
Location: KY
Posts: 973
|
Re: throwout bearing retainer?
Glad to see you got your problem solved.
__________________
The sig says it all. |
01-27-2005, 10:41 PM | #7 |
Registered Member
Join Date: Jun 2001
Location: butler pa
Posts: 303
|
Re: throwout bearing retainer?
one of them anyways
__________________
92lx wannabe saleen |
02-02-2005, 12:53 PM | #8 |
Registered Member
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
|
Re: throwout bearing retainer?
__________________
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Throwout Bearing Blues | Rstng93 | Blue Oval Lounge | 2 | 06-19-2004 07:41 PM |
clutch and throwout bearing questions | bmxmon | Classic Mustangs | 0 | 05-23-2004 04:32 PM |
T5 hard to shift after replacing bearing retainer | Merlin76 | Windsor Power | 8 | 02-20-2004 10:22 PM |
Stock steel bearing retainer? | Merlin76 | Windsor Power | 1 | 04-13-2003 08:42 AM |
Need advice on throwout bearing | RPM427 | Windsor Power | 2 | 08-28-2002 02:05 PM |