![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: May 2000
Location: Kamloops, BC
Posts: 2,875
|
![]() My MAF is toast. I tried to clean it (it was real dirty), but the car won't run right. It will start, idle poorly, surge and miss.
I don't have a lot of money, but don't want to by cap. I'm going to stick with my stock air box, and need an MAF for 19# injectors. I have been looking mostly at the Pro M 75 mm. I don't like what I have heard on the C&L. Any comments? Also anyone know where I can find one? I checked at Dallas Mustang and they only had one without the flange for the stock air box. Since this is my only car, I need something pretty quick. HELP! ------------------ 1995 Mustang GT |
![]() |
![]() |
![]() |
#2 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]() Getting rid of my 75mm Pro-M for the 76mm C&L was the best thing I did, it runs much better now.
I would check out the 76mm, when you upgrade injectors it will only cost $25 for a tube instead of $100 like the Pro-M. You could always make a flange? ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! <B>12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree [This message has been edited by Rick 91GT (edited 10-04-2001).] |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Apr 1999
Location: Overland Park, KS, USA
Posts: 1,631
|
![]() If you're car is mostly/all stock, then I'd say stick with a smaller MAF than a 75mm unit. I doubt it would really hurt you...but it certainly won't help. A 70mm is definitely the largest one you'd need for a stock motor.
------------------ 1984 1/2 GT350 (#842 Hatchback w/ T-tops), 302HO, Comp cams Xtreme Energy cam, Carter 625cfm carb, Weiand Stealth intake, MSD distributor, MSD coil, FMS 9mm wires, 1 5/8" MAC unequal shorties, 2 1/2" MAC Prochamber H-pipe, Flowmaster 2 chambers, KYBs, 16"x8" 4 lug Cobra Rs, Falken 245/45ZR16s So I pushed it up to 110, That flathead motor was about to give in, I crossed my fingers and prayed to the lord, Don't let me down you fuct up ford!" "5-Oh Ford" by The Reverend Horton Heat |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: May 2000
Location: Kamloops, BC
Posts: 2,875
|
![]() Thanks guys. I had to order a unit already and I ordered the 75mm Grenaldi (sp?) unit. I needed a part real fast and could not wait. Does the C&L use the stock electronics? I think my electronics are toast, if I'd need new electronics if it does.
Hopefully this 75mm unit runs well. I'm not looking for big performance gains (yet), I just want the car running. Thanks for the replies. ------------------ 1995 Mustang GT |
![]() |
![]() |
![]() |
|
|