![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Sniffed too much n20
Join Date: Oct 1998
Location: Ont, Canada
Posts: 1,018
|
![]() I was wondering what H-pipe can I use with a set of Heddman full length 1 5/8" headers. Do I need a custom H-hpipe or would any aftermarktet piece work?
|
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Apr 1999
Location: Overland Park, KS, USA
Posts: 1,631
|
![]() I'd think just about any aftermarket H-pipe should fit...as long as it's for long tubes.
------------------ 1984 1/2 GT350 (#842 Hatchback w/ T-tops), 302HO, Comp cams Xtreme Energy cam, Carter 625cfm carb, Weiand Stealth intake, MSD distributor, MSD coil, FMS 9mm wires, 1 5/8" MAC unequal shorties, 2 1/2" MAC Prochamber H-pipe, Flowmaster 2 chambers, KYBs, 16"x8" 4 lug Cobra Rs, Falken 245/45ZR16s |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Oct 1999
Location: Cincinnati, Ohio
Posts: 1,575
|
![]() Just anyone won't fit, because it uses a 3 bolt header flange. When I had them I couldn't find a h-pipe for them so I took them back. I here that headman makes one but have yet to see it. How ever there is a ad in MM&FF and they had a 3 bolt h-pipe but it was 3" and kinda pricey. Good luck man!
------------------ 87 GT, 4 inch cowl hood,17x9 Cobra R's/255/45's,GT-40 heads,long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's. Best time 13.012 Best MPH 104 Best 60' 1.816 Visit my site at: http://www.geocities.com/cobrar93_2000/MyPage.html |
![]() |
![]() |
![]() |
#4 |
Sniffed too much n20
Join Date: Oct 1998
Location: Ont, Canada
Posts: 1,018
|
![]() Luckily I haven't bought them yet, I wanted to see what I'd be getting into if I did.
I might just go ahead and get the MAC longtubes then... |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
SVO Shorty Headers 1-5/8 Question | stangposse | Windsor Power | 0 | 08-07-2003 12:48 PM |
Buying new headers | TwiLighTBluEGT | Windsor Power | 4 | 04-23-2003 08:55 PM |
Anyone have problems with MAC headers?? | HiFlow5 0 | Windsor Power | 15 | 05-30-2002 08:30 AM |
Headers should I or shouldn't I....Need Advice Quick Please | Mustang_GT_90 | Windsor Power | 9 | 05-01-2002 01:16 PM |
BBK one-piece flange or MAC individual flange long tube headers. | Fox Body | Windsor Power | 10 | 04-03-2001 04:25 PM |