![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Feb 1999
Location: Naperville, Illinois, USA
Posts: 35
|
![]() So I have everything disconnected, the tie rods, input shaft pinch bolt, and rack to crossmember bolts. The rack slides off all the way off the passenger side but won't come all the way off the driver side. It seems like it is snagged on something. Any ideas? Do I have to disconnect something else with the input shaft or do I have to keep pulling? Anything else I should know about putting the new one on? Thanks for the help.
__________________
'89 GT- Hurst- 3.55's- MM's subs- 144K miles- 14.31@97.5 |
![]() |
![]() |
![]() |
#2 |
347ci of HORSE POWER!!!
Join Date: Jul 2001
Location: Houston, TX
Posts: 1,416
|
![]() the only thing that you have to worry about is the two power sterring lines, tie rods, sterring shaft and the two LONG blots that hold it to the chassis. Make sure the hoses aren't catching on anything.... if it's the stock one, it might be in there pretty good. spray some brake cleaner everywhere to losen up the dirt. Both sides should slide off evenly. If it's not caught on anything, don't be afraid to give it a good hard pull. You ain't going to use it again, so don't worry about it.
![]() |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
|
![]() Make sure the two lines are disconnected. I replaced one last year and both fitting that allow the nut to turn freely were siezed so I had to cut one line, and rotate the entire rack around the other one. The reason I did this was because the auto parts store was out of stock on the hoses.
I'd rather replace a head gasket then do another steering rack. Good luck and use lots of penetrating oil!
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out! |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Feb 1999
Location: Naperville, Illinois, USA
Posts: 35
|
![]() Thanks for the help guys. I just got home from work and it has been soaking in penetrating oil all night so I'm gonna give it a shot now. I'll let you'll all...
__________________
'89 GT- Hurst- 3.55's- MM's subs- 144K miles- 14.31@97.5 |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Feb 1999
Location: Naperville, Illinois, USA
Posts: 35
|
![]() Right now the entire rack is out except the input shaft. It is stuck in the little bracket that the pinch bolt goes through. Shouldn't it slide out after the pinch bolt has been taken out? I didn't think that I had to take that bracket off.
__________________
'89 GT- Hurst- 3.55's- MM's subs- 144K miles- 14.31@97.5 |
![]() |
![]() |
![]() |
#6 |
347ci of HORSE POWER!!!
Join Date: Jul 2001
Location: Houston, TX
Posts: 1,416
|
![]() You don't have to take the sterring shaft off at the firewall, just where the stupid ghetto rubber bushing is. Glad everything seems to be going good for ya
![]() |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Manual rack versus pwr steering | Stang_ROTY | Windsor Power | 4 | 08-09-2004 02:27 PM |
Rack & Pinion or Stock steering for '67 | Yellow67GTA | Classic Mustangs | 0 | 09-30-2002 10:04 PM |
Steering rack replacement questions. | chris91LX | Windsor Power | 2 | 09-04-2002 11:39 AM |
Steering rack blew | chris91LX | Windsor Power | 4 | 08-26-2002 09:25 AM |
Quick question!! Need help fast please!... Steering wheel question!!!... | WA2FAST | Windsor Power | 3 | 02-14-2002 02:41 PM |