stock springs/ride height

GhettoPop · 03-06-2003, 08:26 PM

Where can I pick up stock ford springs for a 90 GT? Prices? I was told that they come in different rates, but still maintain stock ride height, any truth to this?

Also, what are the positives/negatives to going a little lower, let's say with FMS B springs?

Simi Stang · 03-07-2003, 04:14 PM

I'm pretty sure I have my stock coil springs for my 90'GT still lying around in the garage. I know I've seen the rears recently but can't remember the last time I saw the front pair.

I can look sometime next week. I'm leaving for Florida tomorrow until next Wed. But I'll let you know if I locate all 4 of them once I'm back. If you are interested, I'll sell them to you for dirt cheap.

shad.murray@warnerbros.com

GhettoPop · 03-09-2003, 11:23 PM

Thanks for the offer Simi, but I'm looking for a new set of coil springs that retain stock ride height to replace my stockers. Any info?

03-06-2003, 08:26 PM	#1 (permalink)
GhettoPop Gimme a Drink! Join Date: Dec 2002 Location: NYC Posts: 693	stock springs/ride height Where can I pick up stock ford springs for a 90 GT? Prices? I was told that they come in different rates, but still maintain stock ride height, any truth to this? Also, what are the positives/negatives to going a little lower, let's say with FMS B springs?

03-07-2003, 04:14 PM	#2 (permalink)
Simi Stang Registered Member Join Date: Aug 2002 Location: Simi Valley, CA. Posts: 769	stock 90'GT springs I'm pretty sure I have my stock coil springs for my 90'GT still lying around in the garage. I know I've seen the rears recently but can't remember the last time I saw the front pair. I can look sometime next week. I'm leaving for Florida tomorrow until next Wed. But I'll let you know if I locate all 4 of them once I'm back. If you are interested, I'll sell them to you for dirt cheap. shad.murray@warnerbros.com __________________ '90GT/ 306 w/ Edel. alum. hds. & performer manifold/ 24lb.inj./ B-303/ 1.72 rollers/ TRW frgd.pstns./ JBA hdrs./ MAC 2.5" off-road h-pipe w/ 2-chamber Flows/ Hurst short throw shftr./ Centerforce dual-friction clutch/ subframes/ reinforced torque boxes/ Crane HI-6 ignition/ Crane PS91 coil/ MSD timing retard for 150hp. NOS/ 3.73s/ Lakewood traction bars/ Auburn posi.... 1/4 mile times: on motor= 12.7 @ 108mph on nitrous= 11.6 @ 118mph

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Stock Tire Sizes	GhettoPop	Windsor Power	8	01-19-2003 07:22 PM
AFR 165's or other heads with cam and stock induction	Mustang_GT_90	Windsor Power	27	11-25-2002 03:01 PM
Suspension ?--Bullitt, Eibach, Stock, or COMBO???	rel3rd	Windsor Power	3	10-15-2002 08:53 PM
LT's vs. shorties vs. stock headers	jonnyk	Windsor Power	9	01-01-2001 11:28 AM
2000 Street Stock - the $15,000 question	Tim Miller	Racer's Club House	4	10-20-1999 08:09 PM

03-09-2003, 11:23 PM	#3 (permalink)
GhettoPop Gimme a Drink! Join Date: Dec 2002 Location: NYC Posts: 693	Thanks for the offer Simi, but I'm looking for a new set of coil springs that retain stock ride height to replace my stockers. Any info?

Sponsored Links