stud mount rocker install

Blown 306 · 05-13-2001, 09:55 AM

I need the correct way to do my stud mount rockers. canfield heads and 1.6 rr, F303 cam. Any info on how to do them or a website that shows how would be very nice thanks alot

------------------
450+ hp CAnfield stage 2 heads, s-trim 13psi, daily driven 90 gt(with ac)

Rick 91GT · 05-13-2001, 10:24 AM

Once you get them to 0 lash, you go 1 turn. I went 1 turn on mine and they ended up too tight I had to go in and re adjust and go 3/4 turn. If the rockers are too tight the motor will not rev and have any power you will need to re-adjust them. Here's a link to Crane Cams Installation Instruction of Alum Stud Mount Rocker arms. http://64.90.9.168/cranecams/pdf/425e.pdf

If that doesn't work go to www.cranecams.com installation instructions

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon!

[This message has been edited by Rick 91GT (edited 05-13-2001).]

gray87GT · 05-13-2001, 10:25 AM

Go to the Crane or Competition Cams website, they have basically the same installation instructions.

05-13-2001, 09:55 AM	#1
Blown 306 Registered Member Join Date: May 2001 Location: west palm beach fl usa Posts: 3	stud mount rocker install I need the correct way to do my stud mount rockers. canfield heads and 1.6 rr, F303 cam. Any info on how to do them or a website that shows how would be very nice thanks alot ------------------ 450+ hp CAnfield stage 2 heads, s-trim 13psi, daily driven 90 gt(with ac)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
adjusting valves/ stud mount?? PKRWUD? Anyone??	Simi Stang	Windsor Power	8	07-08-2003 11:43 AM
Anyone running stud mount rockers.	Dark_5.0	Windsor Power	9	03-05-2002 07:53 AM
TFS TW rocker stud Q	drudis	Windsor Power	0	01-22-2002 02:37 PM
Roller Rocker install questions. (long)	chris91LX	Windsor Power	5	03-15-2001 09:32 PM
Adjusting stud mount rockers	The Doc	Windsor Power	2	01-18-2001 06:54 PM

05-13-2001, 10:24 AM	#2
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	Once you get them to 0 lash, you go 1 turn. I went 1 turn on mine and they ended up too tight I had to go in and re adjust and go 3/4 turn. If the rockers are too tight the motor will not rev and have any power you will need to re-adjust them. Here's a link to Crane Cams Installation Instruction of Alum Stud Mount Rocker arms. http://64.90.9.168/cranecams/pdf/425e.pdf If that doesn't work go to www.cranecams.com installation instructions ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! [This message has been edited by Rick 91GT (edited 05-13-2001).]

05-13-2001, 10:25 AM	#3
gray87GT Registered Member Join Date: Jan 2001 Location: Minnesota Posts: 177	Go to the Crane or Competition Cams website, they have basically the same installation instructions.