timing belt snaped...in the rain

tireburner163 · 07-11-2002, 01:44 PM

well if finally happened...that blasted timing belt of my car snaped....in a frickin monsoon.

It looks like a pretty simple task, but I'm just wondering....how do I get it back in time and make sure it's right? Are there dot's or something.

fiveohpatrol · 07-11-2002, 02:07 PM

this belongs in the small ponies forum ******!

I would hope that it has dots or something like that to tell where to line it up at, but then again, maybe not. PKRWUD where are you?

PKRWUD · 07-11-2002, 02:33 PM

Pull the spark plugs. Line up the crank so that the timing pointer lines up at TDC (zero degrees). Pull the cover off, and rotate the cam until the pointer on the sprocket (a little inward pointing triangle) lines up with the pointer on the head (at approx. 5:30, if looking at the cam sprocket). Back off the tensioner, and install the belt. When installing the belt, start at the crank, go around the aux. shaft sprocket, and onto the cam sprocket. Make sure there is no slop in the belt on the aux. shaft side. Run it by the tensioner, and release the tensioner. Replace the cover, but remove the plug in the center, by the head. Rotate the engine by hand through 4 crank revolutions, and double check the timing marks. If they are still good, snap the button it, put in the plugs, attach the wires, and go racing!

Take care,
-Chris

tireburner163 · 07-12-2002, 01:44 AM

now I've gotta pull 8 plugs....DOH!.....8 plugs in a 4 banger...only on a Ford

6T9PONY · 07-12-2002, 01:52 AM

And on a Nissan! My '86 Nissan p/u had a 2.4 4-cyl with 8 plugs...

PKRWUD · 07-13-2002, 05:27 AM

So, how about an update?

Take care,
-Chris

tireburner163 · 07-13-2002, 10:09 AM

Well.....everything is off, except the crank pulley. I used Chris's little trick to get the bolt off, but I think I'm gonna need a puller, cause it ain't goin no where.

I've got the motor at TDC on the compression stroke and I've got the cam in time. Once I get that crank pulley off, I've only got about 20min worth of work(5 for Chris

)

tireburner163 · 07-14-2002, 07:37 PM

Well I've got it all buttoned up and it's running(yay

).

I'm not 100% sure I had the motor at TDC when I installed the belt, I think it's about 2* advanced(yea, like I don't need any more torque

), oh well.....it's not hurting anything. Just thought I'd let Chris know what was up, thanks man you were a big help

....I owe you one.

07-11-2002, 01:44 PM	#1 (permalink)
tireburner163 It's a lot like a race car Join Date: Aug 2000 Location: Meridian, MS Posts: 4,127	timing belt snaped...in the rain well if finally happened...that blasted timing belt of my car snaped....in a frickin monsoon. It looks like a pretty simple task, but I'm just wondering....how do I get it back in time and make sure it's right? Are there dot's or something. __________________ 93 LX hatch h/c/i 357W 07 ZZR 600

07-11-2002, 02:07 PM	#2 (permalink)
fiveohpatrol I'd rather be basketweaving Join Date: Feb 2000 Location: Indianapolis Posts: 2,551	this belongs in the small ponies forum ******! I would hope that it has dots or something like that to tell where to line it up at, but then again, maybe not. PKRWUD where are you? __________________ NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft

07-11-2002, 02:33 PM	#3 (permalink)
PKRWUD Junior Member Join Date: Mar 1999 Location: Ventura, California Posts: 8,981	Pull the spark plugs. Line up the crank so that the timing pointer lines up at TDC (zero degrees). Pull the cover off, and rotate the cam until the pointer on the sprocket (a little inward pointing triangle) lines up with the pointer on the head (at approx. 5:30, if looking at the cam sprocket). Back off the tensioner, and install the belt. When installing the belt, start at the crank, go around the aux. shaft sprocket, and onto the cam sprocket. Make sure there is no slop in the belt on the aux. shaft side. Run it by the tensioner, and release the tensioner. Replace the cover, but remove the plug in the center, by the head. Rotate the engine by hand through 4 crank revolutions, and double check the timing marks. If they are still good, snap the button it, put in the plugs, attach the wires, and go racing! Take care, -Chris __________________ Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local RED & WHITE!

07-12-2002, 01:44 AM	#4 (permalink)
tireburner163 It's a lot like a race car Join Date: Aug 2000 Location: Meridian, MS Posts: 4,127	now I've gotta pull 8 plugs....DOH!.....8 plugs in a 4 banger...only on a Ford __________________ 93 LX hatch h/c/i 357W 07 ZZR 600

07-12-2002, 01:52 AM	#5 (permalink)
6T9PONY All about the Windsor. Join Date: Feb 2000 Location: Omaha, NE Posts: 2,050	And on a Nissan! My '86 Nissan p/u had a 2.4 4-cyl with 8 plugs... __________________ '69 Fastback--351W/C4/Currie 9" Daily Driver--'00 Ranger Supercab XLT, 4.0L/auto/4WD

07-13-2002, 05:27 AM	#6 (permalink)
PKRWUD Junior Member Join Date: Mar 1999 Location: Ventura, California Posts: 8,981	So, how about an update? Take care, -Chris __________________ Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local RED & WHITE!

07-13-2002, 10:09 AM	#7 (permalink)
tireburner163 It's a lot like a race car Join Date: Aug 2000 Location: Meridian, MS Posts: 4,127	Well.....everything is off, except the crank pulley. I used Chris's little trick to get the bolt off, but I think I'm gonna need a puller, cause it ain't goin no where. I've got the motor at TDC on the compression stroke and I've got the cam in time. Once I get that crank pulley off, I've only got about 20min worth of work(5 for Chris) __________________ 93 LX hatch h/c/i 357W 07 ZZR 600

07-14-2002, 07:37 PM	#8 (permalink)
tireburner163 It's a lot like a race car Join Date: Aug 2000 Location: Meridian, MS Posts: 4,127	Well I've got it all buttoned up and it's running(yay ). I'm not 100% sure I had the motor at TDC when I installed the belt, I think it's about 2* advanced(yea, like I don't need any more torque), oh well.....it's not hurting anything. Just thought I'd let Chris know what was up, thanks man you were a big help ....I owe you one. __________________ 93 LX hatch h/c/i 357W 07 ZZR 600

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
351W belt routing	Ieatcamaros	Windsor Power	1	05-02-2003 09:15 PM
Total timing vs initial timing for max HP.	Dark_5.0	Windsor Power	32	04-21-2003 01:49 AM
Timing belt (HELP)	Cora323	Small Ponies	1	02-01-2003 02:08 AM
Check engine light after steeda pullies / timing adjuster!! HELP!!	MineralGray02K	Modular Madness	1	09-29-2002 02:11 AM
points and timing specs	xfernal	Classic Mustangs	1	12-30-2001 04:20 PM

Sponsored Links