Trunk lid

titanium92 · 07-30-2004, 01:13 AM

Hey guys ....I had already posted this in specialty but don't think too many ppl look in there so I'm going to try it here.

Hi guys, I was wondering how the heck I get my trunk lid to work again. The person before me had taken off the trunk lid to put an amp and subs etc. and never bothered to put those cross pieces back I have them here but not installed. So my trunk lid doesn't stay open ( it's a pain in the butt ) and he disconnected the power trunk and the license plate light.
So if anyone could in detail or pics if you have or even a website to show me how to put back those cross pieces would be a GREAT HELP!!

Thanks

lxfiveoh · 07-30-2004, 01:05 PM

Just take a look at someone elses setup. My car was missing the torsion bars altogether.

After many years, I got tired of it and went to the junkyard to check out another notchback. I proceeded to take the torsion bars off of that 'stang and put them in mine.

It's really quite simple...a little bit of a PITA...but simple nonetheless.

Good luck,

titanium92 · 07-30-2004, 02:21 PM

Thanks....thought of that too but don't know where to look for another one, that is why I asked on here. So if anyone else has some pics or detailed explaination would be great thanx.

RPM427 · 07-30-2004, 08:25 PM

Are you guys talking about the gas struts that hold the hatch open?

lxfiveoh · 07-30-2004, 11:06 PM

Negative.

We're referring to the torsion bars/springs/rods that hold up the TRUNK LID on 'coupes'.

One end of each rod is attached to a little hole in the "hinge" to which the trunk lid is bolted. The rod then travels across the trunk compartment below the package tray (while sort of twisted around the *other* rod) and attaches to a 3 or 4 position bracket at the other end of the trunk.

Once you hold them up in there and stare at it for a while, you'll see how they go.

titanium92 · 07-31-2004, 11:48 AM

Thanks lxfiveoh I'm getting closer now, but now what do you mean little hole on "hinge"? I know where to put the rod in the bracket on the one side just can't figure the "hinge" hole side.

07-30-2004, 01:13 AM	#1
titanium92 Registered Member Join Date: Jul 2004 Posts: 38	Trunk lid Hey guys ....I had already posted this in specialty but don't think too many ppl look in there so I'm going to try it here. Hi guys, I was wondering how the heck I get my trunk lid to work again. The person before me had taken off the trunk lid to put an amp and subs etc. and never bothered to put those cross pieces back I have them here but not installed. So my trunk lid doesn't stay open ( it's a pain in the butt ) and he disconnected the power trunk and the license plate light. So if anyone could in detail or pics if you have or even a website to show me how to put back those cross pieces would be a GREAT HELP!! Thanks

07-30-2004, 01:05 PM	#2
lxfiveoh Registered Member Join Date: Mar 2002 Location: Miami, FL Posts: 54	Just take a look at someone elses setup. My car was missing the torsion bars altogether. After many years, I got tired of it and went to the junkyard to check out another notchback. I proceeded to take the torsion bars off of that 'stang and put them in mine. It's really quite simple...a little bit of a PITA...but simple nonetheless. Good luck, __________________ Nelson 1990 Mustang LX 5.0 http://fiveoh.homestead.com

07-30-2004, 08:25 PM	#4
RPM427 Registered Member Join Date: Aug 2001 Location: Huntington NY Posts: 573	Are you guys talking about the gas struts that hold the hatch open? __________________ -1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out!

07-30-2004, 11:06 PM	#5
lxfiveoh Registered Member Join Date: Mar 2002 Location: Miami, FL Posts: 54	Negative. We're referring to the torsion bars/springs/rods that hold up the TRUNK LID on 'coupes'. One end of each rod is attached to a little hole in the "hinge" to which the trunk lid is bolted. The rod then travels across the trunk compartment below the package tray (while sort of twisted around the other rod) and attaches to a 3 or 4 position bracket at the other end of the trunk. Once you hold them up in there and stare at it for a while, you'll see how they go. __________________ Nelson 1990 Mustang LX 5.0 http://fiveoh.homestead.com

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
LX Coupe trunk lid?	titanium92	Appearance & Detailing	0	07-29-2004 11:27 AM
Rattling trunk lid	95GTS	Blue Oval Lounge	5	10-24-2003 08:10 AM
Trunk Lid help????	fast5l	Windsor Power	1	10-29-2001 05:49 PM
Trunk Paint Color?	Kisner	Classic Mustangs	3	09-05-2001 08:52 AM
HELP HELP HELP Stuck in the trunk!	Super_Stang	Windsor Power	5	07-29-2001 11:35 PM

07-30-2004, 02:21 PM	#3
titanium92 Registered Member Join Date: Jul 2004 Posts: 38	Thanks....thought of that too but don't know where to look for another one, that is why I asked on here. So if anyone else has some pics or detailed explaination would be great thanx.

07-31-2004, 11:48 AM	#6
titanium92 Registered Member Join Date: Jul 2004 Posts: 38	Thanks lxfiveoh I'm getting closer now, but now what do you mean little hole on "hinge"? I know where to put the rod in the bracket on the one side just can't figure the "hinge" hole side.