MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 01-29-2004, 10:29 PM   #1
mak375
Registered Member
 
Join Date: Nov 2001
Location: State College, PA
Posts: 104
Default waterbox

Ive only been to the drag strip a couple times and because i was on street tires i just rolled through the waterbox. now i have a set of drag rad's and i think i should warm them up some. What exactly do you do? just rev it up and pop the clutch or should i use the brakes or the parking brake or what?
mak375 is offline   Reply With Quote
Old 01-29-2004, 10:38 PM   #2
420nitro
Registered Member
 
420nitro's Avatar
 
Join Date: Nov 2003
Location: Rockford
Posts: 596
Default Re: waterbox

Quote:
Originally posted by mak375
Ive only been to the drag strip a couple times and because i was on street tires i just rolled through the waterbox. now i have a set of drag rad's and i think i should warm them up some. What exactly do you do? just rev it up and pop the clutch or should i use the brakes or the parking brake or what?
When you are on street tires especially regular tires you should not go threw the water box or even get them wet! All you need to do is just give them a quick spin to clean them off. As goes for the drag radials, I would do the same and smoke them up. In another words, do a dry burn out until you feel a slight drag on the motor or a decent amount of hazing from the tires. Leave the water box for the people running drag slicks.

When you do a burn out with a manual transmission, you simply just dump the clutch to get the wheels spinning and with your left foot press the brake pedal. Try getting some practice on the street to profect this. Once you have mastered this go to your nearest drag strip and give a spin!
Good luck
420nitro is offline   Reply With Quote
Old 01-30-2004, 04:02 PM   #3
mak375
Registered Member
 
Join Date: Nov 2001
Location: State College, PA
Posts: 104
Default

well at the track i go to, there is no dry burnouts and you have to go through the waterbox to get to the lanes, thats why i said i just rolled right thru them when i had street tires.

unfortunatly i live in pittsburgh and with the current weather i cant really take my mustang out especially with drag rad on so i doubt ill be getting much practice until spring when the track opens but thanks for the info.
mak375 is offline   Reply With Quote
Old 01-30-2004, 06:28 PM   #4
Scrapla
Registered Member
 
Scrapla's Avatar
 
Join Date: Apr 2002
Location: Florida
Posts: 532
Default

You cant even go off the track like through the dirrt or rocks, Thats what I do down here at moroso and just clean them off with a burn out, beware of flying rocks!
__________________
90gt 347 and some bolt ons :-)


RICE HATERS MEMBER #73
Scrapla is offline   Reply With Quote
Old 02-04-2004, 10:34 AM   #5
blue oval 50h
Registered Member
 
Join Date: Dec 1998
Location: NJ
Posts: 219
Default

When you roll through the waterbox, dont spin your tires. You will fling even more water into the wheelwells and will eventually drip down on the tires. Do a nice 2nd gear burnout with some smoke.
__________________
347- 10.63@128 N/A
blue oval 50h is offline   Reply With Quote
Old 02-04-2004, 11:57 PM   #6
Coupe Devil
Moderator
 
Coupe Devil's Avatar
 
Join Date: Mar 2001
Location: Myrtle Beach SC
Posts: 1,643
Default Re: Re: waterbox

Quote:
Originally posted by 420nitro


When you do a burn out with a manual transmission, you simply just dump the clutch to get the wheels spinning and with your left foot press the brake pedal.
DO NOT AND I REPEAT DO NOT Jab the brake pedal when you do this .. PRACTICE IT and feather into the brake a little harder every time untill you feel your stopping the motion of the car fast enough and getting a good burnout. I have personally seen a drive shaft and tail shaft desenegrate when the back brakes locked when the driver slammed the brakes. NOT PRETTY
__________________
1990 GT, 347, TFS TW Heads, TFS Cam, TFS Track heat, Twin turbos, FMIC, T5.

Built Ford Tough Moderator
Coupe Devil is offline   Reply With Quote
Old 02-05-2004, 06:28 PM   #7
Ackbar00
Rebel Fleet Commander
 
Ackbar00's Avatar
 
Join Date: Oct 2001
Location: Huber Heights, OH
Posts: 1,003
Default

I think all the basics were covered here. Just chiming in to increase my post count
__________________
1993 Mustang GT, PTK w/ T-64 - My Cardomain Webpage

11.25@123.5 on only 8 psi.
10.84@121 on only 1 headgasket



"The Truth is, Your the Weak, and I am the Tyranny of Evil Men!"

Ackbar00 is offline   Reply With Quote
Old 02-06-2004, 09:53 AM   #8
Kevin Price
Registered Member
 
Kevin Price's Avatar
 
Join Date: Jan 1999
Location: Oxford, KS
Posts: 935
Default

You could also install a roll control to hold your front tires. This is an easy install and is nice if you plan on doing much racing.
__________________
2001 Mustang "Mach 1" SVO siamesed 351 stroked to 417ci,Yates heads, solid roller,Trans King glide.
Best 1/4 ET 9.17 (ALL MOTOR)
Best 1/4 MPH 147

My Car
Kevin Price is offline   Reply With Quote
Old 02-06-2004, 10:33 PM   #9
Ieatcamaros
Domestic Rice really sucks!
 
Ieatcamaros's Avatar
 
Join Date: Apr 2002
Location: KY
Posts: 973
Default

Or, you could do what I do. I wear a 13 shoe, so I say anyone can do this. I hold the brake with my right heel and gas with my right toes. To keep from doing
Quote:
DO NOT AND I REPEAT DO NOT Jab the brake pedal when you do this
what he said. I think this is easier and safer.
__________________
The sig says it all.
Ieatcamaros is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:58 PM.


SEARCH