Welding in subframes and removing front sway bar . What should I run??
 

Right now I am running a 14.79 @93 @3000ft.I have subframes on the way and I am removing my front sway bar.

Right now my 60ft is 2.00. If I pick up any E.T. it should be in the first 60ft (I think) I have had people tell me that subframes make a night and day difference and I have had people tell me that subframes didnt help them at all.

I for sure have a traction problem for the first 70ft I have to baby the car or it goes up in smoke.

I am hoping for a 14.55 or so.



------------------
88 mustang gt convertible bored to 306 BBk equal length headers, mac cold air fender kit, 3.73 FMS gears, Steeds Tri-ax shifter, Steeda underdrive pullies, Custom off road X-pipe, 2 chamber flow masters, cowl hood, nitto drag radials, ford racing clutch, 160* thermostat 16 degrees of timing electric fan off 94' t-bird jacobs electronics cap and wires. Edelbrock 1 1/2 inch drop springs. (Best E.T. 14.79@93mph @3000ft)

I think those 2 mods would drop you to 14.78. http://www.mustangworks.com/msgboard/biggrin.gif j/k. 2 tenths I think is a stretch, but far from impossible. Is that 2.0 60' time on streets rubber, dr's, or slicks? If it's on streets you don't have a traction problem at all.

------------------
'90 LX 5.0;12K original miles;FMS 3.55 gears; March pulleys;Edelbrock Performer Heads;BBK 1 5/8" equal length shorties;MSD 6AL ignition w/ blaster 2 coil;FMS E303 cam;Pro-M 75mm MAF;BBK 70mm TB; Eibach drag-launch spring kit;Southside weld-on subs;9" K&N cone filter charger;Hurst shifter;Cervini 3" turbo hood;A/C delete;gutted cats;2 chamber Flomasters;Corbeau racing seats;FMS 30# injectors;JMS custom chip;Holley 190lb fp;TFS track heat intake (12.299 @ 113mph w/ a 1.78 60')
....soon to be b

I run that 60 ft on nitto drag radials. I leave at an idle and gradualy give it gas.
I would like to be able to dump it 2500 rpm's or so and see what she will do.

14.78 http://www.mustangworks.com/msgboard/biggrin.gif If I run that while beating a camaro I will be happy.



------------------
88 mustang gt convertible bored to 306 BBk equal length headers, mac cold air fender kit, 3.73 FMS gears, Steeds Tri-ax shifter, Steeda underdrive pullies, Custom off road X-pipe, 2 chamber flow masters, cowl hood, nitto drag radials, ford racing clutch, 160* thermostat 16 degrees of timing electric fan off 94' t-bird jacobs electronics cap and wires. Edelbrock 1 1/2 inch drop springs. (Best E.T. 14.79@93mph @3000ft)

I tossed my swaybar and went 1.9 only once, usually in the 2.0 range, but ran on tires in my sig, just radials, and small ones, i have no subframe connctrs, but are coming soon.

your right, the improvement comes in the first 60' if you can get your rpms up just enough to almost spin, but bogg a little, your in for at least 2 tenths improvement.

------------------
90 lx coupe: 5spd, energy susp trans mounts, fms hd clutch, Mac coldair fenderwell, Mac h-pipe, supercoil, ADS chip, 160 stat, aluminum D/S, Black magic fan, 3.27grs.
Best time: 13.9116(on 225/60/15 firehawks)
Best mph: 98.17
Best 60': 1.9607

someday mods:4.10's, slicks.

oh, i should mention, vht is good stuff, the guys at the track (workers) have some stuff works like glue http://www.mustangworks.com/msgboard/biggrin.gif, i launched pretty hard, and felt my rear wheels hopping around, and driveshaft banging, but thats better than just smoking them to the 330ft mark http://www.mustangworks.com/msgboard/smile.gif