![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Registered Member
Join Date: Jan 2000
Location: Mount Joy, PA , U.S.
Posts: 198
|
![]() I have 2 questions
first I am putting a wet adjustable nitrous on my 89 5.0 I have everything except heads and a fuel pump I was wondering can I run a 50 shot on a stock fuel pump ALso How hard is it to remove my fuel pump does anyone have any links to websites that describe it Thanks Eric |
![]() |
![]() |
![]() |
#2 |
Rat Killer
Join Date: Aug 2002
Location: Cold ass Ohio
Posts: 1,143
|
![]() Stock pumps won't handle much over 50. You'd be OK for a very short time, so short in fact I wouldn't even try it.
Fuel pump is easy to do, it's in the gas tank. I don't know of any links, but a Chilton's manual will help you out. Not a bad job to do, some simple hand tools (you'll need the fuel line tools, borrow them from Autozone) a few beers, and a few hours is all you should need. ![]()
__________________
d-Con Racing "Nothing fancy, just 347 inches of RAT POISON!" MICE need not apply..... ![]() |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Aug 2002
Location: SanAntonio, Tx
Posts: 957
|
![]() yea, and disconnect the battery first please
![]()
__________________
X-Texas highway patrol ssp 1990 coupe - exploder Gt-40 iron heads, Explorer intake, 19 lber's. E-cam. crane 1.7 rollers. 190fp. 75mm maf. 65mm tb, tubular subframe connectors, mac cai, Asp crank pulley, T-5, king cobra clutch, flowtech 1-5/8 unequals, mac X-pipe Frpp driveshaft, lakewood Lca's. race weight 3,160 12.69 @ 107.35, 1.71 60' 26x8.5 drag's 3.90 gear 13.20 @ 106.91 - 235/60/15 firestones 2.3 60' 3.27 gear |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Sep 2002
Location: Boston
Posts: 592
|
![]() Here's how to change your fuel pump:
Support the tank with 2 jacks, one on each side. You want a tiny bit of upforce to relieve pressure on the strap bolts. It really helps to drive around until the tank is practically empty. A full gastank is HEAVY. Follow the 2 straps back until you see the two bolts they use to hold up the tank. These and a little bit from the filler tube is all that holds the tank in place. It might take a breaker bar to remove them but do so and try to swing the straps out of the way so the tank doesnt land on them. Go to the filler neck and you will see a little ring with a mounting point on the tank side. This is a filler tube support. Unbolt or saw off. Lower the tank slowly. Now you will see a pair of wiring harnesses, one for the fuel level sender and the other for the pump. Disconnect these. You will also see 2 fittings on the top part of the hump. These are the fuel fittings. You will need to pull the snapclips out. They usually break but seem to continue working just fine if just slid in place and ziptied or taped. Some pump kits come with extra clips. Now drop the tank. It will dangle by the filler neck so you need to slide it sideways to get it out. Now look down at the top of the tank and you will see a circular part. There is a sliding metal ring with small tabes around the base of this circle. Screwdriver into the tab and hammer the back of the screwdriver CAREFULLY. This will usually be crazy stuck. Now pull the assembly out, making sure not to knock the filter off on the bottom of the pump assembly. Unscrew pump, replace and lower it back in being sure to put the pump into the middle of the square baffle inside the tank. Sometimes this comes loose. Now just reverse everything you did and you are all set! Good luck! Pete
__________________
91 GT Carb conversion, holley 600 double pumper, edelbrock performer intake, FMS "C" drop springs, march 1000 underdrive pullies, crane 1.7 roller rockers, GT-40P headers, bassani x pipe, american thunder catback, FMS 4.56's, msd aL6, trunkmount battery, A/C eliminator kit, 3000 stall tci streetfighter, AOD with transgo kit, A+ servo, 300M hardened lockup shaft, kevlar bands and 28,000 gvw trans cooler, 3 core radiator, 300 lbs stripped with a full interior |
![]() |
![]() |
![]() |
#5 |
Rat Killer
Join Date: Aug 2002
Location: Cold ass Ohio
Posts: 1,143
|
![]() Well done Pete! But you forgot the part "There is a sliding metal ring with small tabes around the base of this circle. Spray this ring down with PB Blaster, go have a beer, spray it again, and then.... Screwdriver into the tab and hammer the back of the screwdriver CAREFULLY.
![]() ![]() ![]()
__________________
d-Con Racing "Nothing fancy, just 347 inches of RAT POISON!" MICE need not apply..... ![]() |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
nitrous install question | NotchJohnson | Windsor Power | 0 | 03-02-2002 01:08 PM |
Question about nitrous | blueneonman1 | Windsor Power | 2 | 08-31-2001 12:53 PM |
nitrous question, please help! | acidangel316 | Windsor Power | 7 | 08-10-2001 10:16 PM |
Nitrous Question | BrentK7 | Windsor Power | 10 | 07-19-2001 03:18 PM |
nitrous dry kit question | Yan88gt | Windsor Power | 11 | 06-27-2001 11:07 AM |