12-16-2002, 08:12 PM
| #1 (permalink) |
| Registered Member Join Date: Sep 2002 Location: baltimore, md
Posts: 220
|  What head gaskets and intake gaskets?? What head gaskets and intake gaskets should i use when i put my 58cc AFR 165's on with my cobra intake? Ed Curtis said to use a Graphite head gasket. What Fel Pro numbers do i need? thanks for the help
__________________ 90 LX Hatchback 306, AFR 165's 58cc, E303, 1.6 roller rockers, 70mm throttle body, cobra intake, bbk fenderwell, bbk longtubes, x-pipe, flowmasters, pullies, msd 6a, crane ps-92, stock MAF sensor, electric fan, No AC, No air pump, flaming river quick ratio rack C-4, 3500 stall, 373's, aluminum driveshaft SSM Lift bars, , sub frame connectors, strut tower brace 12.57 @105.12mph w/ 1.686 60ft before bbk longtubes (with equal shorties) ----------------------------------------- 86 tube chassis coupe - the trailor queen |
|      |
|
12-17-2002, 02:41 PM
| #2 (permalink) |
| Moderator  Join Date: Dec 1999 Location: Livonia, MI, USA
Posts: 1,194
| See this link for a parts list of what I used: http://www.dariusrudis.com/mustang/new_engine
__________________ Darius Rudis, Moderator Corner Carvers Delight 1989 Mustang LX - Open Track Car http://www.dariusrudis.com |
|
| |
|
12-17-2002, 10:07 PM
| #3 (permalink) |
| Sober voice of Reason  Join Date: Nov 1998 Location: Kelowna, B.C., Canada
Posts: 1,508
| It'll probably be the Fel pro 1250 intake gasket. My heads were opened up to the 1250. I've currently got 1262's on it though because I blew out my silicone end seal and noone had a 1250 that day so I figured that at least it was big enough. works fine. Just wait until you get the heads and then measure.
__________________ F4TE 351w block 393 stroker: Scat 3.85" crank, scat H beams, Probe SRS pistons, Proformed 750 DP holley, Vic jr intake, AFR 205's, Buddy Rawls hydraulic roller cam, Crane 1.6 Gold race rockers, Powerforce SFI balancer, centerforce steel flywheel. Kooks 1 3/4" headers, Spec stage III clutch, Dr. Gas 3" x-pipe, spintech pro streets, TKO-600, Moser 31 splines, Detroit Locker. Just about back on the road... |
|
| |
|
12-20-2002, 04:20 AM
| #5 (permalink) |
| Registered Member  Join Date: May 1999 Location: Indiana
Posts: 512
| I am using the ROL's... Forget the part number though. They are a little harder to find but I have heard a lot of good things about them!! I also like the new Fel-pro's...
__________________ 92GT Lowered with Ebiach's and Koni's, Kenny Brown subframe connectors, lower G-brace and jacking rails. BBK upper and lower control arms, polyurethane bushings all around and Ken Bell blower, ram-air, 80mm mass air, SMC Alky Injection kit, J&S Knock Gaurd, TwEECer RT and a bunch of other stuff! |
|
| |
| Sponsored Links | |
| | |
 |
| Thread Tools | |
| Display Modes | Rate This Thread |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| blown head gaskets!!!! (read) | 11secondGT | Windsor Power | 9 | 08-27-2002 09:54 PM |
| which gaskets to run with Holley intake edelbrock heads | NewAge 5.0 | Windsor Power | 3 | 01-26-2002 04:38 PM |
| lower intake gaskets? will they work? | DemonGT | Windsor Power | 3 | 06-08-2001 07:40 PM |
| Head Gaskets, Header Gaskets, Intake Gaskets, etc | AxemanZZ | Windsor Power | 8 | 01-11-2001 01:09 PM |
| Boss 429 head gaskets!! | 93CobraR | Classic Mustangs | 4 | 03-13-2000 07:28 AM |
Linear Mode
