Who has best price on 31 spline axles?

8850 · 04-21-2001, 04:45 PM

I have my 347 almost ready to run again and need 31 spline axles with c clip eliminators. Also need a spool.

------------------
88 347, Twisted wedge heads,Comp Cams 224/230 cam, 1/4=10.718 @ 123.02 mph dyno= http://www.fbody.com/members/LarryS/mustdyno.jpg

Mach 1 · 04-22-2001, 11:31 AM

Try BB&T racing. They advertise in MM&FF.

------------------
1993 GT/AOD
'93 Mustang GT

8850 · 04-22-2001, 02:18 PM

Thanks Mach 1!

IMPULSERACING · 04-22-2001, 08:24 PM

I just got mine directly from Strange. They sell 31 spline axels with the c-clip elim kit for $374.50. For another ten bucks they'll install the c-clip eliminators. There number is 847-869-7010. Hope this helps.

------------------
92' LX Hatch 5 spd Edelbrock Performer Intake, pro-m 75mm MAF, 70mm T.B., 24lb injectors, 190lph, Mac fenderwall cold air induction, mallary ignition and coil, Cobra 1.7 rockers, BBK full length headers, 373:1 gear, upper and lower control arms, supersubs, 50/50's, Eibach front drag springs, Moroso rear trick springs, no sway bar, battery in hatch, compucar N20 kit

8850 · 04-22-2001, 09:39 PM

IMPULSERACING,

I have found some Moser 31 spline axles for a little less than $385, $310 to be exact. However, I don't know if the c clip elims are installed. I need to do a little more investigating.

One distributor of Moser said that some machining to the axles is required on the Moser if you do not order with the c clips already installed.

Also, did you have to cut off some of your housing to fit the Strange? I have a copy of the Moser instructions and you are suppose to saw off 1/4".

[This message has been edited by 8850 (edited 04-22-2001).]

04-21-2001, 04:45 PM	#1
8850 Registered Member Join Date: Nov 1998 Location: Sugarland, TX USA Posts: 161	Who has best price on 31 spline axles? I have my 347 almost ready to run again and need 31 spline axles with c clip eliminators. Also need a spool. ------------------ 88 347, Twisted wedge heads,Comp Cams 224/230 cam, 1/4=10.718 @ 123.02 mph dyno= http://www.fbody.com/members/LarryS/mustdyno.jpg

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
93 cobra rear have 31 spline axles????	dragstang86	Windsor Power	1	08-01-2003 09:11 PM
need 28 spline axles in So Cal	stng87	Windsor Power	3	02-19-2003 09:17 PM
Moser Axles Snapped In Two! Brand New!	12secAOD	Windsor Power	1	08-06-2002 09:14 AM
want 31 spline axles have rear disc breaks can anyone help?	93 Cobra needs input	Windsor Power	6	02-28-2002 08:22 AM
28 vs 31 spline aftermarket axles?	DirtKing	Windsor Power	4	04-19-2001 08:25 AM

04-22-2001, 11:31 AM	#2
Mach 1 Registered Member Join Date: May 1999 Location: Georgia Posts: 3,866	Try BB&T racing. They advertise in MM&FF. ------------------ 1993 GT/AOD '93 Mustang GT

04-22-2001, 02:18 PM	#3
8850 Registered Member Join Date: Nov 1998 Location: Sugarland, TX USA Posts: 161	Thanks Mach 1!

04-22-2001, 08:24 PM	#4
IMPULSERACING Registered Member Join Date: Dec 1999 Location: chicago,IL,USA Posts: 158	I just got mine directly from Strange. They sell 31 spline axels with the c-clip elim kit for $374.50. For another ten bucks they'll install the c-clip eliminators. There number is 847-869-7010. Hope this helps. ------------------ 92' LX Hatch 5 spd Edelbrock Performer Intake, pro-m 75mm MAF, 70mm T.B., 24lb injectors, 190lph, Mac fenderwall cold air induction, mallary ignition and coil, Cobra 1.7 rockers, BBK full length headers, 373:1 gear, upper and lower control arms, supersubs, 50/50's, Eibach front drag springs, Moroso rear trick springs, no sway bar, battery in hatch, compucar N20 kit

04-22-2001, 09:39 PM	#5
8850 Registered Member Join Date: Nov 1998 Location: Sugarland, TX USA Posts: 161	IMPULSERACING, I have found some Moser 31 spline axles for a little less than $385, $310 to be exact. However, I don't know if the c clip elims are installed. I need to do a little more investigating. One distributor of Moser said that some machining to the axles is required on the Moser if you do not order with the c clips already installed. Also, did you have to cut off some of your housing to fit the Strange? I have a copy of the Moser instructions and you are suppose to saw off 1/4". [This message has been edited by 8850 (edited 04-22-2001).]