![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Apr 2002
Location: VANCOUVER,CANADA
Posts: 43
|
![]() The time has come for me to replace my stock shifter with a short throw type. I have had a problem with a bit of gear grinding going up into second and some times into third. Only when booting it around on the street. It sure takes the wind out of your sails when you grind gears during a street race. Don't know if the transmission will explode or not.
My question is what type to buy? What kind of shifters have you guys had good luck with and would recommend. I have heard Steed Triax mentioned a lot. My mechanic said Hurst is good, sounds kind of old though. And a Saleen dealer ship her recomends thier shifter. Any help is always appreciated. |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Mar 2002
Location: Zeeland, Mich.
Posts: 16
|
![]() I've been running the PRO 5.0 since the beginning of the summer, and its great. And the spring loading is really nice to, especially for the 2-3 shift.
|
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: May 2002
Location: Chapel Hill, NC - USA
Posts: 188
|
![]() I'd suggest the steeda Tri Ax shifter, or the B&M.
Torinalth
__________________
When you finally shut down the car, just sit back and remember the run.... win or lose, you know it was a surge of adreneline |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Mar 2002
Location: Dexter City, Ohio
Posts: 60
|
![]() I just bought a Steeda Tri-Ax for my 02 GT today. It should be here in a couple of days and I will tell you how I like it.
|
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Jun 2002
Location: Pittsburgh
Posts: 5
|
![]() i've had the Steeda Triax for 2 months now. it is so much better than stock. i've driven a stang with a B&M shifter, and didn't find it as positive as the Steeda.
also, the Steeda has a high and a low position for mounting the handle. the high position puts it to the same height as the stock, and the low makes it about 3 inches lower. i have tried it in both, and it takes alot of work for me to get it into 5th when it is in the low position. i just keep it in the high setting now. Party ON!
__________________
Bob 98 GT K&N cold air intake Cherry Bomb Vortex mufflers 3.73's Steeda Tri-ax shifter |
![]() |
![]() |
![]() |
#6 |
The Redneck James Bond
Join Date: Sep 2000
Location: Fayetteville NC
Posts: 1,707
|
![]() I so GO STEEDA Tri Ax. Its a great shifter. I've felt Pro 5.0's in other cars and wasnt all that crazy about them, but everyone has there preferances.
As for your grinding...Hmm...Doesnt sound good. Maybe you should get the tranny looked at first before putting on a short Throw Shifter.
__________________
64 1/2 "D" code Red Mustang Coupe. Red Baron, 2000 Perf Red Mustang GT. 5spd. Stage 2 CNC heads with Large Valves, Comp Cams (270-274 dur .550 lift), Forged Crank, DRP pistons, Manly H-beams, Pro M 87 mm Mass Air, 24lb Inj, 75mm TB, Plenum Spacer ,Long Tube Headers, Homemade H-pipe, 2 chamber Flows, 4:10's, Steeda Tri-Ax, LKW 70/30's, Eibach Drag Springs, Steeda SubFrames, Battle Boxes, Rear Girdle, Adj uppers, Alunimum Drshft, Southside Lift Bars. Project Cars, 64 1/2 6cyl coupe, 1930 Model A Nostalgia Rod. |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: May 2002
Location: Cincinnati, Ohio
Posts: 57
|
![]() I've had a PRO 5.0 in mine since about March. It is a definite improvement. But any aftermarket shifter would be better than the stock and you'll probably be happy with any of them. The shorter height may be an issue for you though so you should go with one that adjusts.
|
![]() |
![]() |
![]() |
#8 |
Guest
Posts: n/a
|
![]() STEEDA Tri Ax....nuff said!!
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: Apr 2002
Location: VANCOUVER,CANADA
Posts: 43
|
![]() Thanks to all for the great response. Based on your guys experience i am going with the Steeda set to the high adjustment.
I hear nothing but good about Steeda. This will be my first mod to my 96 GT rag top. I will post again when I get the price plus installation. I unfortunately can not do it my self, sad I know. Next is Cat backs. I am thinking either Bassini or 3 chamber Flow Masters. FM's up here are about $550 (cat back) and Bassini are about $850. Canadian dollars. Thanks again for all the help. Oh Ya, I think I exaggerated the gear grinding a bit. But you know how it is, ya want to make sure that you have it in gear before you pop the clutch when you have serious acceleration in mind. |
![]() |
![]() |
![]() |
#10 |
Guest
Posts: n/a
|
![]() Good choice to go with the Steeda Tri Ax, but I would suggest putting the shifter handle on the LOW setting....the shifts will be even shorter than the high setting(although the high setting is still shorter than stock throws). As far as the Cat back, go with the BASSANI(like i did
![]() |
![]() |
![]() |
#11 |
midnightruns.com
Join Date: Dec 2000
Location: Ottawa, Ontario, Canada
Posts: 584
|
![]() I had the B&M in my 2000GT... it was ok.
A buddy had the saleen... sucked ***. Never tried the Pro5.0 but I know the Steeda is THE BEST. A buddy of mine has it... and it is AMAZING! Adjustments are perfect... and clicks when you shift... you won't be able to get better. Worth every dollar.
__________________
![]() NEW CAR! - 2002 GT TrueBlue - Best Stock ET - 13.77 Old Lizard - 2000GT Electric Green - Best ET STOCK: 13.662 @ 100.2MPH |
![]() |
![]() |
![]() |
#12 |
Registered Member
Join Date: May 2002
Location: maryland
Posts: 32
|
![]() i have a steeda for about 6 months . no problems go with a steeda!
|
![]() |
![]() |
![]() |
#13 |
College Stanger
Join Date: May 1999
Location: Aiken,south carolina, usa
Posts: 1,097
|
![]() I have had the steeda for alittle of a year now. At first it was alittle tight but after a month it loosened up alot. I had it in the high postion and my buddy with a 98 cobra and a b&M shifter said I do not like it it is too high. So I took 10 mins lowered it and its great. The moral of the story: I can lower or raise mine. He cannot. I love my Steeda to death. I put the Steeda Clutch Quad set up on withmy steeda shifter. It is the greatest. GET IT YOU WILL NOT REGREAT IT. Good Luck.
__________________
2003 Sonic Blue Cobra |
![]() |
![]() |
![]() |
#14 |
Registered Member
Join Date: Jun 2002
Location: Victoria BC
Posts: 10
|
![]() The two best are the TriAx and the pro 5.0.I have the TriAx and love it.I have done quite a bit of work to my 2000 GT and the TriAx is one of my favorite.
|
![]() |
![]() |
![]() |
#15 |
GRNSNAK
Join Date: Jun 2002
Location: Slidell Louisiana
Posts: 65
|
![]() I have been using the Hurst shifter for over a year now and love it. Its got adjustable positive stops, and getting in gear is crisp, and i have never messed up a shift sence the install, it was a definate improvement. But yes, it seems everyone i know uses the Steeda shifter. I just thought i would say something about the Hurst, sence no one else has.
|
![]() |
![]() |
![]() |
#16 |
Registered Member
Join Date: Apr 2002
Location: VANCOUVER,CANADA
Posts: 43
|
![]() I have the Steeda installed now. Sure works nice. Very positive shifts. No missing 3rd now. I am actually surprised that the shifting distance does not seem much shorter. The knob is up at at the stock shifter height. Maybe I should lower it.
The one thing I don't like about it is that it seems to transmit a lot more noise into the car. Is that normal or did the guy who installed it screw some thing up. The cost up here for the shifter was approx $310 plus installation and tax. The guy offered me a Steeda knob for $79, I said no thanks. Nice but I am sticking with stock appearance for now. Thanks again for all of your input. |
![]() |
![]() |
![]() |
#17 |
Guest
Posts: n/a
|
![]() I was one of the first to respond to this same thread, and suggested you should set the shifter handle height to the LOW setting.
![]() |
![]() |
![]() |
#18 |
Registered Member
Join Date: Apr 2002
Location: VANCOUVER,CANADA
Posts: 43
|
![]() Do any of you know how to remove the plastic surround from around the shifter on a 1996 to access the shifter. I would like to try it in the lower position.
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Suggestions On Short Throw Shifters | OnMy3rdStang | Stang Stories | 13 | 11-30-2001 07:21 PM |
Short Throw Trouble Anyone? | CobraFire98 | Modular Madness | 0 | 07-01-2001 10:23 AM |
Hurst short throw, vs stock shifter?? | 90dpscoupe | Windsor Power | 1 | 05-30-2001 03:17 AM |
Short throw shifter | swtstang | Windsor Power | 5 | 05-22-2001 01:40 PM |
Short throw shifters | fazali | Blue Oval Lounge | 6 | 01-04-2001 12:32 PM |