![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Aug 2001
Location: Saratoga Springs
Posts: 30
|
![]() I have aquired a 90 GT Recently that I installed a 70mm tb and Comp engineering intake and a high volume fuel pump. I now hear a strange vacuum whistle and the car runs like crap. The idle is irratic and this morning it blew a huge white cloud of smoke. I always smell fuel and the plugs are white. If I disconnect the vacuum for the fuel regulator it idles better.
Anyone know where to start? |
![]() |
![]() |
![]() |
#2 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() I am assuming that vacuum whistle is coming from the tb..Let me guess? BBK or edelbrock tb??
If you are running your stock heads, you might be pushing to much air into the motor..I would try switching the intakes back until you got a set of better flowing heads or as a matter of fact, take your heads off and port them yourself! Good Luck.. ------------------ 347 Stroker Motor: Balanced, Cobra Transmission, Extrude Ported and Polished Upper and ported Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, 30lb Bosch Injectors, Holley AFPR, March Underdrive Pulleys, Perma-Cool Fan, 3-Core Radiator, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 73mm Vortech MAF, 70mm TB, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, AC and Smog del, rear seat del. |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Aug 2001
Location: Saratoga Springs
Posts: 30
|
![]() The TB is BBK. But the intake is Comp Eng. The TB whistle is on all BBK's but this whistle is way different, it is almost like a howl.
|
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Mar 2001
Location: college station, tx
Posts: 143
|
![]() Does it have heads? If not, then the 70 is too big in the first place. You have coolant coming from either your egr plate or your lower intake, assuming you did do the lower. Hence the white smoke. I used to have that howl after I did my heads / cam. Turns out I was way rich due to a faulty FPR, and the egr valve was doing it. I think there was so much unburned gas in the exhaust that it caused it to howl. Does it get louder when you press the gas? It went away after I put on a new regulator. I think that was the most annoying and embarassing think I've ever heard on my car.
------------------ Clint L. White 95 Cobra #3637 58cc GT40X heads with mild porting, Crane 2031 cam, FRPP 65 TB, 1.7s, Cobra intake, homeade cold air, 155lph, pullies, Tokico Illuminas, C springs, GW LCAs, Kenny Brown super subs, Steeda CC plates, aluminum driveshaft, Steeda quadrant, B&M ripper, Kirban FPR, MSD6A, Taylor wires, Mac shorties, off road hpipe, 2 1/2 ultra flows w/ dumps, R hood, Euro clear corners, stock 3.08s 13.61 @ 105.7 w/ 2.22 <-- 284 rwhp / 323 rwtq |
![]() |
![]() |
![]() |
#5 | |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]() Quote:
The 70mm is a little big for a mostly stock motor, a 65mm would be better for now. If I remember correctly the Comp is just a upper that fits onto the stock lower or a GT40 lower. I would first check to make sure the gasket between the EGR spacer and intake isn't leaking, I bet that is where the coolant is getting into the intake. White smoke is coolant, blue is oil. You can bypass that spacer by plugging the two hoses that go into the EGR spacer. The coolant pre-heats the motor when it is cold, helps it idle better. I have had mine bypassed for a couple years no with no issues what so ever. If the coolant is leaking into the intake it will make your plugs white, the water is cleaning everything off. CHeck that gasket first ![]() No for the gas smell, if you have off roads you may smell it more then normal, also make sure you didn'y unplug or crush the vent hose that coms out from the top of the fuel tank when you swapped fuel pumps. The one line runs from the top of the tank to a metal tube that turns into a black plastic tube that runs to the charcol canister on the passenger side frame rail. Fuel Pressure should be 38 and timing 14-16 (10 degrees is stock) ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! <B>12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree [This message has been edited by Rick 91GT (edited 09-05-2001).] |
|
![]() |
![]() |
![]() |
#6 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() WOE!!! my bad..didnt make sense to me either..what I was meaning is that with the bigger Intake and stock heads, there might be some bottlenecking going on...Does that sound better or am I still confusing others and myself?? I better go get some sleep..
------------------ 347 Stroker Motor: Balanced, Cobra Transmission, Extrude Ported and Polished Upper and ported Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, 30lb Bosch Injectors, Holley AFPR, March Underdrive Pulleys, Perma-Cool Fan, 3-Core Radiator, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 73mm Vortech MAF, 70mm TB, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, AC and Smog del, rear seat del. |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Aug 2001
Location: Saratoga Springs
Posts: 30
|
![]() This make sence to me. The fuel pump was not installed by me so I will have to check that. When you change a fuel pump to a hi volume do you need to change the regulator?
------------------ 86 GT - BBK Equal shorties, BBK H-pipe, Flowmasters, 70mm Tb, BBK cold air intake. Automatic. 96k miles. |
![]() |
![]() |
![]() |
#8 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() no, you do not have to install a new regulator..
------------------ 347 Stroker Motor: Balanced, Cobra Transmission, Extrude Ported and Polished Upper and ported Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, 30lb Bosch Injectors, Holley AFPR, March Underdrive Pulleys, Perma-Cool Fan, 3-Core Radiator, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 73mm Vortech MAF, 70mm TB, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, AC and Smog del, rear seat del. |
![]() |
![]() |
![]() |
#9 |
Tubbed and Juiced
Join Date: Mar 2001
Location: Tulsa, Oklahoma
Posts: 1,861
|
![]() ***The TB whistle is on all BBK's but this whistle is way different, it is almost like a howl.
My BBK 70mm TB did not "whistle" one bit. ------------------ 1989 GT, 3:55's, full exhaust, 4 in. hood, Pro 5.0, Have many other parts 4 sale. All parts for sale now. 2000 Camaro SS-A4, 13.7's bone stock. 1989 Chevy S-10, EX. Cab-383(500+hp on motor), trick flow heads, trick flow pistons, etc... autometer phantom gauges, "built" 700R4, roll cage, lexan back window, corbeau seats, R.H.S. 5 harnesses, Fuel cell, convo pro wheels, 15x14's with 29x18.5 M/T'S on back, 15x4's on front, nitrous, and so much more! |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
1988 Gt - 1998 Gt Hp Each Year | steedamustang01 | Modular Madness | 13 | 05-09-2002 07:26 PM |
1996 Cobra vs 2000 Mustang GT | Milktasd | Stang Stories | 2 | 04-05-2002 03:11 AM |
RESULTS - Grand Prix GT vs. Celica GTS | 302 LX Eric | Stang Stories | 7 | 09-25-2001 06:46 PM |
ran a '01 GT | EZRIDN | Stang Stories | 3 | 08-29-2001 08:17 PM |
Just got my '89 GT! Time slip guesses? | 84stangLX | Blue Oval Lounge | 6 | 07-25-2001 09:44 PM |