MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 09-02-2002, 01:19 AM   #1
5000cc
Registered Member
 
Join Date: May 1999
Location: Hialeah,Fl,USA
Posts: 57
Unhappy Leaking Tranny

Guys, I crawled underneath my car today and spotted a big stained along the right side of the car frame. I noticed that there was a leakage coming from where driveshaft meet tranny. I installed this tranny about a year ago, it is an overhauled cobra tranny. Now, I don;t know if I damaged the seal when I installed the driveshaft or defected from the company that I purchased it from. Anyway, my question to you guys is can i change that seal in the back or tranny or I have to take that sucker out ( again?) to have professional do it? ( and that would be sucks big time ). May be Autozone may have the replacement seal for that or what? anybody?

Thanks guys.
__________________
93 Lx coupe,125 shots wet system,BBK headers,pully,ported performer intake,24 lbs,short belt,Headman x pipe,mac catback,upr blue thunder shifter,73 mm mass air,k&n panel filter,king cobra cluth, aluminum driveshaft, 4.10 gears, cobra tranny, welds 15/6 on front and 15/10 rear.
5000cc is offline   Reply With Quote
Old 09-02-2002, 05:34 AM   #2
PKRWUD
Junior Member
 
PKRWUD's Avatar
 
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
Default

You can do it yourself, and in less than an hour. Get a replacement seal, and a couple quarts of fluid. Pull the driveshaft, and pry out the old seal. Inspect the yolk on the end of the drive shaft, and make sure it doesn't have any burrs or uneaven wear that might have caused the seal to fail. Install the new seal with some fluid around the inner seal edge, and reinstall the driveshaft. Check the fluid level, and add accordingly.

Take care,
~Chris
__________________
Webmaster:
Rice Haters Club
Jim Porter Racing
Peckerwoods Pit Stop


Support Your Local
RED & WHITE!
PKRWUD is offline   Reply With Quote
Old 09-02-2002, 10:18 AM   #3
5000cc
Registered Member
 
Join Date: May 1999
Location: Hialeah,Fl,USA
Posts: 57
Default

Thanks, Chris, I will run to the store to get that seal, it's good to have people like you hanging around here to help people like me. I'd send you a six pack!!

Thanks again
Tap.
__________________
93 Lx coupe,125 shots wet system,BBK headers,pully,ported performer intake,24 lbs,short belt,Headman x pipe,mac catback,upr blue thunder shifter,73 mm mass air,k&n panel filter,king cobra cluth, aluminum driveshaft, 4.10 gears, cobra tranny, welds 15/6 on front and 15/10 rear.
5000cc is offline   Reply With Quote
Old 09-02-2002, 12:28 PM   #4
PKRWUD
Junior Member
 
PKRWUD's Avatar
 
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
Default

Quote:
Originally posted by 5000cc
I'd send you a six pack!!

Thanks again
Tap.
How about you donate $10 to your local homeless shelter instead.



Take care,
~Chris
__________________
Webmaster:
Rice Haters Club
Jim Porter Racing
Peckerwoods Pit Stop


Support Your Local
RED & WHITE!
PKRWUD is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
leaking tranny fluid GhettoPop Windsor Power 5 01-13-2004 07:57 PM
Tranny leaking at base of dipstick nightzeus Classic Mustangs 4 06-12-2003 08:41 PM
HELP! Tranny won't stop leaking!!!! rel3rd Windsor Power 3 10-29-2002 08:10 AM
AOD HELP! Tranny lines leaking! 88COBRA Windsor Power 1 09-06-2001 05:32 PM
Leaking C-4 tranny Mac_5.0 Windsor Power 0 09-04-2001 08:15 PM


All times are GMT -5. The time now is 10:03 AM.


SEARCH