|
Rebuilt Tranny = Piece of $#@% - Part II
Well, after all this work pulling the tranny out and reinstalling it twice I was hoping it would be done and have all these headaches behind me. But alas, I was dreaming I guess. Now the tranny won't stay in reverse and it grinds in 2nd gear.
I'm going to take it back to the shop in Indy and shove it up someone's @$$ and tell them if they don't get it right this time I'm going to demand a FULL refund on top of the $250 labor I am demanding now plus an additional $250 labor for having to pull it out again. Anybody have a good Tremec for sale cheap? ------------------ Too much to list. Best ET on the car so far with stock 2.73 gears - 13.73@102mph Indiana Stangers Association Buy your parts here ICQ# 42269241 |
Damn dude... I've seen some shitty rebuilds on T-5's before but your luck is one of the worst. I got my T-5 from D&D performance in MI, since a rebuild costs as much as a new one, hehe.
|
Yeah, it's great looking at my Stang up on blocks. And driving my wife's purple Neon around is starting to give me a complex. I feel like a flamer in that damn thing.
I guess owning the car for a year with 125,000+ miles on it and not having a single problem should have been a sign that sh!t was about to hit the fan and splatter everywhere. ------------------ Too much to list. Best ET on the car so far with stock 2.73 gears - 13.73@102mph Indiana Stangers Association Buy your parts here ICQ# 42269241 |
Hey Kev, sorry to hear you are still haveing tranny problems... Among other things I would demand a differant tranny this time if I were you. And for what it is worth I don't think you are a flammer, well not yet anyway. LOL Man, you better get on them so you can have your car ready for saturday!! Good luck dude! http://www.mustangworks.com/msgboard/cool.gif
------------------ 92GT all the free stuff and a few bolt-ons, lowered with Ebiach's and Koni's, Kenny Brown subframe connectors, lower G-brace and jacking rails. BBK upper and lower control arms, polyurethane bushings all around and Ken Bell blower, ram-air, 80mm mass air, etc. |
i just sent my t5 to a guy in pa who rebuilds mustang trannies (manuals).all he does is rebuild those type trannies he really knows his **** . my trans was rebuilt by prevois owner but wasn't done right.it took this guy 2 minuets to tell me all about my trans and what was probly done wrong during last rebuild.go to this guys web site check it out www.hanlonmotorsports.com . if you want to still go with your shop (ie because they have your money)then tell them that you want them to cusult with this guy to find out what they are doing wrong..my trans was doing similer things guy said that input shaft might not have been shimed right.if you can get refund then send trans to him or bye one of his rebuilds .....he also deals with tremecs could set you up with one of them........good luck
------------------ old guy with 87 gt....well not so old guy |
Bob Hanlon is a nice guy and so is his wife, I just bought a good bit of my parts from him. When this T-5 dies which I hope isn't anytime soon I am going to have him build me a Badd A** Tremec.
Kevin, it really sucks to see you having this many problems, I would ask for a new tranny and ask them to take money off for all the labor you have put in it, I think that is only fair. If not you can ship it to me and I'll rebuild the damn thing. Do you know if Tim D. has gotten to the track yet? I used to talk to him a good bit but have lost contact with him since the move and I was bustin' A** on my car. Ask him to drop me a e-mail if you talk to him. Rick ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! |
why dont u try an aod? the shop here rebuilt mine and 3 hard abusing yrs later it is still holding up fine. he charged $1,700, but he put it in
------------------ My slo aod- 3.73s, pullies, flowmasters, h-pipe, bbk cold air, and 13.42 in the 1/4 @ 103 mph |
I can't afford another tranny at the moment. At least not unless I could get my money back from these %$#@ers. I'm driving the car to them this morning and let them see for themselves. Well, wish me luck guys. I'm driving the car to Indy busted tranny and all (70 miles). 2nd gear is toast, but the other gears should hold up fine right?
------------------ Too much to list. Best ET on the car so far with stock 2.73 gears - 13.73@102mph Indiana Stangers Association Buy your parts here ICQ# 42269241 |
Well, I called the tranny shop and talked to them finally. The guy asked me if I was using the stock shifter and I told him I had a Pro 5.0. He then informed me that the aftermarket shifters tear up transmissions and I was like HUH?!
He also said shift forks don't bend in a T5. Hmm. We got ourselves a winner boys! |
shifter forks do not bend..... they are cast aluminum. cast alum does not bend, it breaks.
you should have never said anything about the aftermarket shifter, anything not factory will give the trannyshop an excuse to say why it broke. just say everything was factory origional. |
im not a T-5 driver, but isnt one of the big reasons to get an aftermarket shifter to NOT tear up your tranny?
------------------ 88 Notchback 5.0, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, Crane 1.7's, BBK headers, off-road H-pipe, flowmasters, subframe connectors, 65mm TB, shift kit, March ram air kit, motorsport wires, MSD coil, upper and lower control arms, 155lph fuel pump, cheap 2800 stall, Crane Adj.FPR, best time- 13.99@99.75, not yet tested times after rockers,intake or ported heads |
Well, I'm not too worried about them saying it's my fault now. The Ford dealer I took the tranny to initially is going to tell them to make good on this PLUS labor charges or they are pulling all of their business from them http://www.mustangworks.com/msgboard/biggrin.gif
Not to mention I didn't even get to move the car more than a foot before it jumped out of reverse. And after finally getting it out of my driveway and went for a drive it was grinding in 2nd gear and I was babying it. ------------------ Too much to list. Best ET on the car so far with stock 2.73 gears - 13.73@102mph Indiana Stangers Association Buy your parts here ICQ# 42269241 [This message has been edited by 2FastLX (edited 05-14-2001).] |
I had similar agony with my T-5 the best advice is to have a reputable shop do the work for you. I still have a Piece of Crap T-5 in my garage that blew a $470 sized hole in my wallet, that simply will not shift into reverse and chatters in second. When my small claims case finally settles he will get a nice bill for triple damages and the cost to remove and replace the trans. Buyer beware I learned my lesson the hard way.
Now the previously screwed up trans I took out was rebuilt for $575 by a local shop and works great and I am happy now http://www.mustangworks.com/msgboard/biggrin.gif The other trans awaits surgical implantaion in the ripoff artists bunghole http://www.mustangworks.com/msgboard/eek.gif ------------------ Frank W 90 5.0 LX coupe Daily driver. Silencer removed, K&N filter. Flexalite fan, 3 core radiator. FMS flywheel and Clutch 88 Notch 2.3L 5 speed Parts/beater car 74 Chevy Laguna Type S-3 305 fixing soon, getting a 454 to put in garage My two Notchbacks www.chevellepages.com/folingo |
I'm on my 3rd T-5!! I feel your pain! The stock one went at 102,000 miles racing a Vette at Moroso when I hit third gear... http://www.mustangworks.com/msgboard/eek.gif Replaced it with a World class one and that went about 2 years later when the main shaft broke destroying the casing and all that good stuff! This one, I'm hoping will last a while!! Good luck, man!! We can sympathize!!
------------------ Joe! 1988 GT, 167,000 miles!!! 13.71@105mph Check out my listing! Click here! Or my website: www.joe4speed.com 1999 Ninja ZX-6R 10.32@135mph! 1993 Olds Eighty Eight LSS |
I'm off to pull it for this damn thing for the 3rd time. I'm trying to think happy thoughts as I do this so I'm not too pi$$ed by the time I get to the shop.
------------------ Too much to list. Best ET on the car so far with stock 2.73 gears - 13.73@102mph Indiana Stangers Association Buy your parts here ICQ# 42269241 |
I dropped the tranny off yesterday and the guy that owned the place threw it up on a bench and had it apart in less than 2 minutes. He really looked like he knew what he was doing so I don't understand why I am having all these problems. He also mentioned that he put a heavy duty bearing retainer on it but it was still made out of aluminum. I thought the heavy duty ones were steel?
------------------ Too much to list. Best ET on the car so far with stock 2.73 gears - 13.73@102mph Indiana Stangers Association Buy your parts here ICQ# 42269241 |
Quote:
------------------ Clint L. White 95 Cobra #3637 58cc GT40X heads with mild porting, Crane 2031 cam, FRPP 65 TB, 1.7s, Cobra intake, homeade cold air, 155lph, pullies, Tokico Illuminas, C springs, GW LCAs, Kenny Brown super subs, Steeda CC plates, aluminum driveshaft, Steeda quadrant, B&M ripper, Kirban FPR, MSD6A, Taylor wires, Mac shorties, off road hpipe, 2 1/2 ultra flows w/ dumps, R hood, Euro clear corners, stock 3.08s 13.61 @ 104.7 w/ 2.22 |
Yes they are Steel only, just because he can take it apart doesn't mean he can put it back together http://www.mustangworks.com/msgboard/wink.gif
Good Luck Kev ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! |
Well, he said they couldn't find a damn thing wrong with the tranny and they tore it completely apart and put it back together. I don't have very high hopes now. If I put it back in and it still grinds I'm taking it to the track anyway and throwing some slicks on it and thrashing this damn thing until the car won't move. He'll surely find something wrong with it then. Then I'm going to demand my tranny back that I had originally, $400 labor, $60 for gas driving back and forth to Lafayette and Indianapolis, $20 in tranny fluid, and more than likely court costs. I'm sick of this.
What makes it good though is if he doesn't make it good he'll lose all business with the Ford dealer in Lafayette which is a bunch. ------------------ Too much to list. Best ET on the car so far with stock 2.73 gears - 13.73@102mph Indiana Stangers Association Buy your parts here ICQ# 42269241 |
hey maybe this is a stupid question ...but you did adjust the stops on the pro 50 to make sure its going all the way in gear....i dont mean to insult you but ive done things were i've gotten mad and overlooked simple things ,but then thats me
|
| All times are GMT -5. The time now is 11:22 AM. |