MustangWorks.com : Ford Forums

MustangWorks.com : Ford Forums (http://forums.mustangworks.com/index.php)
-   Windsor Power (http://forums.mustangworks.com/forumdisplay.php?f=8)
-   -   scanner not seeing ecm (http://forums.mustangworks.com/showthread.php?t=49029)

Mustzilla 10-08-2006 01:09 PM
scanner not seeing ecm
 
Hi, wondering if any one has encountered this or knows if I might be correct in my thinking. I've had my 95 GT at two garages and they have hooked up under the dash and under the hhod two differant scanners and don't see anything can't recieve memory info nothing you don't hear the senors clicking when put into engine on mode. Could this be a sign the computer has died? Anyone have any thoughts. By the way car still starts and runs by not like it should.

Gearhead999 10-09-2006 09:05 PM
Re: scanner not seeing ecm
 
Yep, could be the ECM. Are all the wires good, not bent or rusted?? If everything is hooked up and you have good, solid, clean connections next thing to try is ECM.

Jeff Chambers 10-10-2006 07:49 AM
Re: scanner not seeing ecm
 
OBDII port on a 94/95 is not an active port. You'll notice that there are only four pins in the connector. It had very limited uses on these cars and did not become fully functional until 96 (at least for the V8 Mustang). Make sure that you're using the correct test connector under the hood. There is a connector by the battery/drivers shock tower that is actually the ABS test connector even though it looks identical to the EEC test connector. It's usually got a red cover to it. You'll find the EEC test connector over by the passenger's shock tower. It is usually black. Don't forget that you need the separate STI connector (single wire/connector) to initiate the test sequence.

PKRWUD 10-10-2006 02:54 PM
Re: scanner not seeing ecm
 
Traditionally, when a Ford OBDI ECM goes bad, a few things happen; The fuel pump stays on as long as the key is in the Run position, the engine will crank over, but won't start, and the ECM won't be able to be reached or have any codes pulled from it.

Mustzilla 10-10-2006 10:58 PM
Re: scanner not seeing ecm
 
Quote:
Originally Posted by Gearhead999
Yep, could be the ECM. Are all the wires good, not bent or rusted?? If everything is hooked up and you have good, solid, clean connections next thing to try is ECM.

I had a local garage do it he tryed under dash and under hood even took it to another shop to see if it was his scanner and same resolts nothing, was advised to take to a dealer. Car does run but not like it did or should..

Mustzilla 10-10-2006 11:00 PM
Re: scanner not seeing ecm
 
Quote:
Originally Posted by Jeff Chambers
OBDII port on a 94/95 is not an active port. You'll notice that there are only four pins in the connector. It had very limited uses on these cars and did not become fully functional until 96 (at least for the V8 Mustang). Make sure that you're using the correct test connector under the hood. There is a connector by the battery/drivers shock tower that is actually the ABS test connector even though it looks identical to the EEC test connector. It's usually got a red cover to it. You'll find the EEC test connector over by the passenger's shock tower. It is usually black. Don't forget that you need the separate STI connector (single wire/connector) to initiate the test sequence.

I had a local garage do it he tryed under dash and under hood even took it to another shop to see if it was his scanner and same resolts nothing, was advised to take to a dealer. Car does run but not like it did or should..


All times are GMT -5. The time now is 10:45 AM.