I need your approval.
 

I know this has been discussed many times b4, but....... I just need your approval. http://www.mustangworks.com/msgboard/smile.gif

In less than a week, I plan on buying a 4" cowl induction hood for '79-'82 Mustang.

I'm pretty much set on buying it from either Cincinatti Composites or Motion Performance (I think most of you haven't even bought from or head of Motion P).

Yeah I heard that CC's quality was questionable, but I also heard they have addressed that issue and recently committed to producing higher quality hoods.

Anyways, sounds good? Just always like to get a second opinion. Thanks.

-----------------------------------------
351W-powered 1979 Ford Mustang notchback
Stock 5.8L under custom made 4" cowl, C4 w/ shift kit
Holley 750 cfm, Edelbrock Performer RPM intake
1 5/8" MAC shorty headers, Al driveshaft
2.5" Off road H-pipe, 2-chamber Flowmasters
Front: 225/60/15, Rear: 255/60/15 Eagle GT II
Weld wheels (15x6;15x8), 8.8" Rear w/ 3.55s
14 x 4” K&N air filter Only a couple of weeks b4 Project FOX begins!!! http://www.mustangworks.com/msgboard/cool.gif

"Red, thou art my companion. Hasten now your quickened metamorphosis to Green that I may conquer all who dare abide there beside me. May they be left thither behind burnt black." ---Fox Body


[This message has been edited by Fox Body (edited 08-31-2001).]

No, AND DON'T SUGGEST CERVINI! They have forgotten where the Fox Body stangs originated from-- the '79. They show preference to 87-93 stangs and have forgotten about the '79s. No they don't make a '79 4" cowl hood, so screw 'em http://www.mustangworks.com/msgboard/tongue.gif.

-----------------------------------------
351W-powered 1979 Ford Mustang notchback
Stock 5.8L under custom made 4" cowl, C4 w/ shift kit
Holley 750 cfm, Edelbrock Performer RPM intake
1 5/8" MAC shorty headers, Al driveshaft
2.5" Off road H-pipe, 2-chamber Flowmasters
Front: 225/60/15, Rear: 255/60/15 Eagle GT II
Weld wheels (15x6;15x8), 8.8" Rear w/ 3.55s
14 x 4” K&N air filter. Only a couple of weeks b4 Project FOX begins!!! http://www.mustangworks.com/msgboard/cool.gif

"Red, thou art my companion. Hasten now your quickened metamorphosis to Green that I may conquer all who dare abide there beside me. May they be left thither behind burnt black." ---Fox Body

[This message has been edited by Fox Body (edited 08-31-2001).]

What about Harwood? I have a "lift-off" style hood from there and I think it is very good quality. If I had to do it all over again, I would get the bolt on style instead.
If I remember correct, they offered quite a few different stlyes for the 79-82 stangs and their prices were competitive.
IMO, I would consider a Harwood hood.


------------------
'82 GT 351W C-4,BBK headers,Carter 625 carb,Comp.Cam,Flowmaster exhaust.
1988 GT...T-5,bone stock

Yes, you're right 82 GT. I have considered them, but I forgot to mention them + I didn't think anyone on here has ordered anything from them.
Also I called them to send me a catalogue and they said they would but I never received it.

How much did yours cost? You say good quality? How long have you had it? Do you think you could post a picture of it here?

Thanks for responding BTW, buddy.

-----------------------------------------
351W-powered 1979 Ford Mustang notchback
Stock 5.8L under custom made 4" cowl, C4 w/ shift kit
Holley 750 cfm, Edelbrock Performer RPM intake
1 5/8" MAC shorty headers, Al driveshaft
2.5" Off road H-pipe, 2-chamber Flowmasters
Front: 225/60/15, Rear: 255/60/15 Eagle GT II
Weld wheels (15x6;15x8), 8.8" Rear w/ 3.55s
14 x 4” K&N air filter. Only a couple of weeks b4 Project FOX begins!!! http://www.mustangworks.com/msgboard/cool.gif

"Red, thou art my companion. Hasten now your quickened metamorphosis to Green that I may conquer all who dare abide there beside me. May they be left thither behind burnt black." ---Fox Body

I almost bought a hood from harwood but it was a pin on and I was looking for a bolt on and they did not have it in stock. It was also a little more money that I had at the time.

The quality was great, it looked real good and I have seen the bolt on hoods from them and they look good also.

------------------
James Cox
nochevy@hotmail.com
1991 Mustang LX
12.565 @109.38mph 1.764 60ft