Tremec TKO - is it worth it?
 

Need your opinions. As some of you know, I've broken my second T-5 in a year. It will cost $2,500 for a TKO with bellhousing, yoke, driveshaft, shifter, and I also believe the clutch.

Is this worth doing? I want to run on a set of 10" slicks and make an 11 second pass. Is there a cheaper transmission that can hold up to the abuse?

------------------
Russ L
'91 LX
Procharger, 3 row intercooler, extrude honed Cobra intake, Mac full Length Headers, 30# inj., 73mm C&L, 75mm tb, E303 cam, 289 rods, ported E7 heads, MSD, T-Rex w/255 lph Walbro, 5 lug conversion, Cobra R wheels, 3.27 gears and Moser Axles.

I think you should do it. It's alot of money but it's nice having a tranny you don't have to worry about. The tremec 3550 would be cheaper and no driveshaft yolk or special clutch. The only difference in the two are the input/output shaft is beefed up in the TKO.

However since you are in the 11's and will probably want to go faster I would get the TKO.

My buddy broke 3 t-5's so when I went stick I went straight to 3550. So far so good.

Bite the bullet, survive at the track and sleep at night. Good luck.

------------------
82 Mercury Capri 302, Comp. Cams, Tremec 3550, 3.73's, 12.8@106 N/A
Kevin's Capri
Kevin's Mustang

Definately worth it. I broke an aod, and then a t-5 before i went to a tremec tko. I wish i would have gone straight for the tko in the first place and saved money. It's expensive at first. But figure in the cost of a couple of t-5's and then a super tough tko won't sound so bad.

------------------
vortech s trim,edelbrock 6032's, b303, cobra intake, 70mm tb, pro m 75mm bullet, granatelli alum. rad., accel 330+ digital ign., msd boost tim. ret., 30# inj., 190 lph fuel pump, t-rex pump, bbk, press. reg., tremec tko, ram billet flywheel, dual friction clutch, pro 5.0 shifter, 4.10 gears, aluminum quadrant, motorsport alum. driveshaft, hooker headers, off road h pipe, flowmaster cat back, subframes, megabyte jr lowers, heavy duty uppers, eibach springs drag springs, koni sport shocks, polish

What's a T-56 goin for these days?

About $2,300-2,500.

------------------
89gt,3.73's,tremec
3550,Steeda
tri-ax,aluminum
driveshaft,Asp
underdrives,Flowmast

$2195 at Hawaii Racing http://www.hawaiiracing.com/fordform.html (bottom of the page).

Take care,
-Chris

------------------
Retired Moderator
MustangNet

My site: Peckerwoods Pit Stop

http://homepage.mac.com/pkrwud/.Pict...sc./MyMac.jpeg

My teams site: Jim Porter Racing

RACECAR spelled backwards is RACECAR

HEY !!! Are you ASE Certified ??? If you are, ask me about iATN.

Hmmm...the T-56 was a possibility, but I was afraid the total parts cost would exceed 3 Large. I'm breaking the bank at $2500, and I don't really need a 6th gear.

------------------
Russ L
'91 LX
Procharger, 3 row intercooler, extrude honed Cobra intake, Mac full Length Headers, 30# inj., 73mm C&L, 75mm tb, E303 cam, 289 rods, ported E7 heads, MSD, T-Rex w/255 lph Walbro, 5 lug conversion, Cobra R wheels, 3.27 gears and Moser Axles.

If you were going with a T56, I woud def. go with a Viper T56, and that cost like $3200+ with everything. If your going the tremec route, I would really consider looking into the new TKO II.

------------------
-1989 GT, not stock.
-2000 Camaro SS-A4,
-1989 Chevy S-10, EX. Cab-383, RPM air-gap intake, demon carb., tubbed, trick flow TW heads, trick flow pistons, 6" rod's, etc... autometer phantom gauges, "built" 700R4, roll cage, lexan back window, corbeau seats, R.H.S. 5 harnesses, Fuel cell, convo pro wheels, 15x14's with 29x18.5 M/T'S on back, 15x4's on front, nitrous, 4 inch cowl hood, Ford 9", auburn Pro-series Posi, Pro-billet distributor, Sanderson Jet-hot coated headers, Custom radiator,

Does anyone know if you can get a bellhousing/clutch/flywheel setup to bolt a TKO II up to a 460 block?

------------------
86 Mustang GT w/pretty stock 93 5.0 (e-cam,pulleys,injectors, throttlebody,h-pipe,headers) Swapping out the 302 for a 514 stroker(was a 429)-cobrajet heads, solid roller cam, victor intake, TKO II trans, 3.73's w/axles&c-clip eliminaters.

Yeah you can, they do it all the time in the cobra replica cars. Tremec bolted up to a 460. I've heard only good things about D&D Performance. Give them a call, I'm sure they could help you out.

www.ddperformance.com
(248)-926-6220