MustangWorks.com : Ford Forums - View Single Post - Will I see 340-350FWHP with this combo, please respond

Killercanary · 02-02-2001, 06:41 PM

I have a 95 GT convert with the following: edlbrock intake, 65mm t-body, shorty headers, off road X pipe, ASP underdrive pulleys, 2 chamber flowmasters, 3.73's, alum. D.S., HD clutch, GW subframe connectors, 13* timing, and a K&N w/ homemade air inlet. These parts took me from a 15.2 at 90mph to a 13.8 at 98mph. I just bought a set of AFr 165/58cc heads, and with them I will add a 75mm Pro-M MAF, 24/30lb injectors, 190lph fuel pump, roller rockers, and a cam yet to be determined. My goal is a trap speed of 105mph, which will require 340-350FWHP, is it possible with the increased breathing of the new heads/cam, and the compression increase associated with the 58cc heads? I may mill them to 54cc's if i have to to achieve my goal.

------------------
95 GT convt' 5 speed, 3.73's,FMS HD clutch, Pro 5.0 shifter, ASP alum. underdrive pulleys, Bassani offroad X pipe, 2 chmbr flowmasters, K&N w/o silencer, edelbrock performer intake, FRPP 65mm T-body, FRPP shorty headers, FRPP aluminum driveshaft.Hooker 4pt chrome car bar, Xenon/Wings West ground effects, custom interior
Best ET: 13.83
Best MPH: 98.55mph with Best 60': 1.91 on Nitto DR's
Homepage: <A HREF="http://www.angelfire.com/pa2/killercanary" TARGET=_blank>http://www.angelfire.

02-02-2001, 06:41 PM	#1
Killercanary Registered Member Join Date: Nov 1999 Location: Altoona, PA Posts: 336	Will I see 340-350FWHP with this combo, please respond I have a 95 GT convert with the following: edlbrock intake, 65mm t-body, shorty headers, off road X pipe, ASP underdrive pulleys, 2 chamber flowmasters, 3.73's, alum. D.S., HD clutch, GW subframe connectors, 13* timing, and a K&N w/ homemade air inlet. These parts took me from a 15.2 at 90mph to a 13.8 at 98mph. I just bought a set of AFr 165/58cc heads, and with them I will add a 75mm Pro-M MAF, 24/30lb injectors, 190lph fuel pump, roller rockers, and a cam yet to be determined. My goal is a trap speed of 105mph, which will require 340-350FWHP, is it possible with the increased breathing of the new heads/cam, and the compression increase associated with the 58cc heads? I may mill them to 54cc's if i have to to achieve my goal. ------------------ 95 GT convt' 5 speed, 3.73's,FMS HD clutch, Pro 5.0 shifter, ASP alum. underdrive pulleys, Bassani offroad X pipe, 2 chmbr flowmasters, K&N w/o silencer, edelbrock performer intake, FRPP 65mm T-body, FRPP shorty headers, FRPP aluminum driveshaft.Hooker 4pt chrome car bar, Xenon/Wings West ground effects, custom interior Best ET: 13.83 Best MPH: 98.55mph with Best 60': 1.91 on Nitto DR's Homepage: <A HREF="http://www.angelfire.com/pa2/killercanary" TARGET=_blank>http://www.angelfire.