NOS bigshot

RPM427 · 06-20-2002, 03:13 PM

what is the smallest shot of horsepower you can jet the NOS bigshot plate system to? It is described as 150-300 horses. Can you jet it any smaller to start with? or do I have to start with 150?

Eric4Nitrous · 06-20-2002, 06:30 PM

yes, you can jet it much smaller if you need. It just says 150-300 but it's not required that you start out at 150. Hope this helps.

Eric

RPM427 · 06-21-2002, 07:26 AM

Thanks, I thought that was the case. What size increments do the NOS jets come in?

mspears · 06-25-2002, 09:48 AM

Just by looking at your signature, it appears you have the Holley intake. Do they make a Big Shot plate for that particular intake?

Thanks,
Mark

RPM427 · 06-25-2002, 11:43 AM

Anderson Ford Motorsports has it in thier catolog as a new item, but summit doesn't stock it, and I can't find a part # from NOS's website. Joes from mustang magic in deer park LI says it cannot be jetted smaller then 150, I think i'm going with TNT nitrous.

Rick 91GT · 06-25-2002, 01:07 PM

NOS is going to make a plate kit for the Holley but it has not been released although it has been advertised..Holley keeps giving me the run around on the release date.

TNT supposedly can make a custom plate to fit the Holley although I can never get anyone to call me back from there, even after getting a inside contact from a NMRA racer.

The only company I currently know producing a plate kit for the Holley upper is TOP GUN, Anderson does sell those kits as well, Stage 5 kit (plate system) which is good for up to 300hp is like $575, the Stage VII (Plate system) kit is $730 and is dual stage capable.

NX makes a neat looking direct port kit for the Holley but you need to drill and tap the intake for the nozzles.

Mach 1 · 06-25-2002, 11:56 PM

It cant be jetted smaller than 150 from what NOS told me themselves, as I e-mailed them directly about the big shot plate system.

Why go less than 150? I think 150 is a good shot...go for it!

RPM427 · 06-26-2002, 07:40 AM

well, I am stuck with a completley stock bottom end (pistons too) for the next year or so, and don't want to grenade my engine. The reason I wanted to go with the bigshot (if it could be jetted smaller to start out) is becuase I am getting a bullet 331 short block from DSS racing with the sportsmans block option and would like to spray a 300+ shot. That way I wouln't need to buy another system when I get a better engine.

Mach 1 · 06-26-2002, 12:29 PM

stock bottom end will handle 150 shot with no problems at all. go for it.

06-20-2002, 03:13 PM	#1
RPM427 Registered Member Join Date: Aug 2001 Location: Huntington NY Posts: 573	NOS bigshot what is the smallest shot of horsepower you can jet the NOS bigshot plate system to? It is described as 150-300 horses. Can you jet it any smaller to start with? or do I have to start with 150? __________________ -1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out!

06-20-2002, 06:30 PM	#2
Eric4Nitrous Registered Member Join Date: Jan 2002 Location: Va Posts: 1,122	yes, you can jet it much smaller if you need. It just says 150-300 but it's not required that you start out at 150. Hope this helps. Eric __________________ 68 Camaro Gene Fulton 632ci Two stages of Jug 8.41 164mph Rockingham 1-26-03

06-21-2002, 07:26 AM	#3
RPM427 Registered Member Join Date: Aug 2001 Location: Huntington NY Posts: 573	Thanks, I thought that was the case. What size increments do the NOS jets come in? __________________ -1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out!

06-25-2002, 09:48 AM	#4
mspears Registered Member Join Date: Mar 1999 Posts: 47	Big Shot on a Holley intake? Just by looking at your signature, it appears you have the Holley intake. Do they make a Big Shot plate for that particular intake? Thanks, Mark

06-25-2002, 11:43 AM	#5
RPM427 Registered Member Join Date: Aug 2001 Location: Huntington NY Posts: 573	Anderson Ford Motorsports has it in thier catolog as a new item, but summit doesn't stock it, and I can't find a part # from NOS's website. Joes from mustang magic in deer park LI says it cannot be jetted smaller then 150, I think i'm going with TNT nitrous. __________________ -1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out!

06-25-2002, 01:07 PM	#6
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	NOS is going to make a plate kit for the Holley but it has not been released although it has been advertised..Holley keeps giving me the run around on the release date. TNT supposedly can make a custom plate to fit the Holley although I can never get anyone to call me back from there, even after getting a inside contact from a NMRA racer. The only company I currently know producing a plate kit for the Holley upper is TOP GUN, Anderson does sell those kits as well, Stage 5 kit (plate system) which is good for up to 300hp is like $575, the Stage VII (Plate system) kit is $730 and is dual stage capable. NX makes a neat looking direct port kit for the Holley but you need to drill and tap the intake for the nozzles. __________________ *D/R 10108 NMRA Drag Radial, 25.5 chassis, F1R* *Check out RNH Performance Performance Engines and Custom Fabrication.* *From Mild to Wild we can build what you want, when you want it.* FOR SALE Stainless Steel Torque Box Supports

06-25-2002, 11:56 PM	#7
Mach 1 Registered Member Join Date: May 1999 Location: Georgia Posts: 3,866	It cant be jetted smaller than 150 from what NOS told me themselves, as I e-mailed them directly about the big shot plate system. Why go less than 150? I think 150 is a good shot...go for it! __________________ 2002 GT 1993 GT (SOLD) '93 Mustang GT RHC member #142

06-26-2002, 07:40 AM	#8
RPM427 Registered Member Join Date: Aug 2001 Location: Huntington NY Posts: 573	well, I am stuck with a completley stock bottom end (pistons too) for the next year or so, and don't want to grenade my engine. The reason I wanted to go with the bigshot (if it could be jetted smaller to start out) is becuase I am getting a bullet 331 short block from DSS racing with the sportsmans block option and would like to spray a 300+ shot. That way I wouln't need to buy another system when I get a better engine. __________________ -1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out!

06-26-2002, 12:29 PM	#9
Mach 1 Registered Member Join Date: May 1999 Location: Georgia Posts: 3,866	stock bottom end will handle 150 shot with no problems at all. go for it. __________________ 2002 GT 1993 GT (SOLD) '93 Mustang GT RHC member #142