![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Registered Member
Join Date: Jun 2002
Location: Massachusetts
Posts: 157
|
![]() Does anyone know how much an estimated cost is to rebuild the clutch pak in an 8.8" rear? I recently blew my posi, because I noticed the car doesn't peel out as good as it use to and there is only 1 tire mark.
__________________
1991 Mustang GT Conv: 58,000 original miles, 2nd owner. Engine: FMS 65mm tb/spacer, C&L 73mm maf, MAC cai. Drivetrain: Built AOD w/ Edge 2800rpm lockup converter, hardened 3-4 inner shaft, Trans-Go shift kit, B&M supercooler, FMS 3.73 gears & aluminum d/s, rebuilt traction lock. Exhaust: BBK unequal length shorty headers, BBK o/r h-pipe, Flowmaster 2 chamber mufflers. Chassis/suspension/brakes: Kenny Brown supersubs. The rest is stock. |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Feb 2002
Location: Nebraska
Posts: 86
|
![]() I have seen new FMS clutch packs for as low as 40 to as high as 60 for the new clutches and steels. Plus you figure 12 to 15 bucks for the friction modifier, and new gear oil and gasket. I'd guess just under a hundered bucks to do it right.
__________________
Proud RHC member #99 1990 Mustang GT Trick Flow heads,F303,Mac cold air,FMS 65mm tb,73mm ma,FMS 1.6,GT-40 intake,MSD igintion,NOS Big Shot@150,Mac equal shorties,Mac h-pipe,American Thunder flows,Centerforce dual friction,TTC 3550,alm drive shaft, 3.73's, HPM subframes, k-member brace, strut tower brace.. amongst others. |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Oct 1999
Location: Pierre Part, La. U.S.A.
Posts: 1,850
|
![]() In Houston, Tx. Pyle Bros Perf. Differentials. You get 4 clutches per side, shims, a heavy duty center spring, and instructions. For $100.00. My last one, lasted 6 years, I just redone it. Look at my 60ft, it speaks for itself.
__________________
88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid ![]() |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Jul 2002
Location: Manteca,Ca.
Posts: 114
|
![]() Go for the metal clutch pak, stay away from the fiber. You only need to add 2 bottles of friction modifier instead of one. I burned up my fiber clutch pak in 2 months. Metal grabs a lot better.
__________________
98 cobra convt. 515 rwhp 421 torque..554 rwhp on 98 octane..635 rwhp this summer |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Loud "pop" after clutch install, won't go into gear.. | Chris_H | Windsor Power | 3 | 08-11-2003 06:24 PM |
T-5 swap & cable clutch problem | LuvMyStang | Classic Mustangs | 0 | 03-19-2003 08:47 AM |
'65 - Pull Away Problems - Action Plan | geordie | Classic Mustangs | 0 | 05-14-2002 01:43 PM |
Clutch Problems | blue302 | Windsor Power | 3 | 09-10-2001 01:37 PM |
billed 5 times to install clutch by Pauls Auto, please read and give opinions (long) | beefcake | Blue Oval Lounge | 2 | 02-23-2001 03:05 PM |