![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Registered Member
Join Date: Mar 2004
Location: Long Island
Posts: 58
|
![]() im going from gt40 Y heads to AFR 185's will my headers bolt right up to my AFRs? thanks guys
***i read that post about AMP performance , i gotta baaaad feeling! i better get my sh!t , and on time too !
__________________
1990 Mustang GT Engine- 308 (bored .40 over) Probe Forged pistons (10.5:1), Scat forged crank and rods, w/Main Girdle, AFR 185 heads, GT-40 intake, CSI electric water pump. AC delete kit, No smog pump, Manual rack and pinion steering. Ignition- MSD 6AL, MSD Blaster coil, MSD hellicore wires. Drive Train- Tremic 3550, Alum. Drive shaft, 3:73 gears, Stock carrier and axels. 26X11.5 M/T Et streets. Power adder- 175 shot of laughing gas. Best ET 11.5 @120mph on squeeze, 12.4 @109mph on muscle (on gt40 heads) on the 185 heads ... ??? tba |
![]() |
![]() |
![]() |
#2 |
Rat Killer
Join Date: Aug 2002
Location: Cold ass Ohio
Posts: 1,143
|
![]() I think you're OK, but double check with AFR. Not sure if they raised the exhaust port on the 185's or not. That'd be the only reason your headers won't fit.
On a side note, that stock T5 (In your signature) isn't going to put up with that for too long. 3rd gear synchro's are gonna head south on you soon, if they haven't already.
__________________
d-Con Racing "Nothing fancy, just 347 inches of RAT POISON!" MICE need not apply..... ![]() |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Mar 2004
Location: Long Island
Posts: 58
|
![]() hahaha, i have to update my profile... i have a 3550 gear box in there now
![]()
__________________
1990 Mustang GT Engine- 308 (bored .40 over) Probe Forged pistons (10.5:1), Scat forged crank and rods, w/Main Girdle, AFR 185 heads, GT-40 intake, CSI electric water pump. AC delete kit, No smog pump, Manual rack and pinion steering. Ignition- MSD 6AL, MSD Blaster coil, MSD hellicore wires. Drive Train- Tremic 3550, Alum. Drive shaft, 3:73 gears, Stock carrier and axels. 26X11.5 M/T Et streets. Power adder- 175 shot of laughing gas. Best ET 11.5 @120mph on squeeze, 12.4 @109mph on muscle (on gt40 heads) on the 185 heads ... ??? tba |
![]() |
![]() |
![]() |
#4 |
Rat Killer
Join Date: Aug 2002
Location: Cold ass Ohio
Posts: 1,143
|
![]() Well that's WAAAAY better! You can even get the G Force goodies for that box. Wish they made good stuff for my TKO
![]()
__________________
d-Con Racing "Nothing fancy, just 347 inches of RAT POISON!" MICE need not apply..... ![]() |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Aug 2002
Location: Rochester
Posts: 553
|
![]() Should be fine with the heads.
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
SVO Shorty Headers 1-5/8 Question | stangposse | Windsor Power | 0 | 08-07-2003 12:48 PM |
Buying new headers | TwiLighTBluEGT | Windsor Power | 4 | 04-23-2003 08:55 PM |
Cylinder head swap | 86pony | Windsor Power | 4 | 09-09-2001 11:12 PM |
Which Head Gasket should I use? | capri302 | Windsor Power | 1 | 05-08-2001 05:33 PM |
Cylinder Head Swap | Fostang | Windsor Power | 0 | 05-05-2001 09:51 PM |