![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Registered Member
Join Date: Dec 1998
Location: Richmond, Virginia
Posts: 449
|
![]() I just got the heads off of my car, and while I was doing the other work, I figured that I may replace the oil pan gasket and oil pump.
Is doing this with the block in the car as hard as it sounds? Jacking the engine up? Dropping the pump in the pan? etc, or is there an easy(easier) way without pulling it? thanks
__________________
1982 Mustang GT |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Aug 2001
Location: Miami, Fl, USA
Posts: 69
|
![]() Hi, I just replaced my oil pump for the second time and now consider myself an expert in this field. The first time I did this while the motor was out. The second time while the motor was on. ---All you gotta do is unbolt the motor mounts, radiator(leave it in though), unbolt the trans mount(so the tranny can up and dn) and disconnect the pos cable. Jack up the motor fm the crankshaft(carefully) till the motor is up against the firewall. This will give you several inches but I was still not able to remove the oil pan. This is ok cause I was able to unbolt the pan then remove the oil pump w/the pick up attached. Not an easy task but very do-able. I would also recommend placing some wood blocks between the motor mounts incase the jack slips. Good luck..
__________________
85GT 5.0 was CFI converted to Holley 650. Hooker full length headers, FlowMaster 2 chamber. Weiand Stealth manifold. 86 roller motor, crane 1:7:1 alum rocker arms(roller). SSI 220@.050/498 Roller cam. Summit double roller timing chain. Melling oil pump, stock bottom end. Mallory Hi-Fire ignition. Under drive pulleys. Accell coil and Ford Motorsport 9mm wires. 93'8.8 posi. 4:10s. AOD w/B&M shift kit. No figures yet, still working on it. No back seats or AC. 1989 GT Convert-- All stock w/AOD, Air Silencer removed, DynoMax Mufflers. |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Feb 2009
Posts: 3
|
![]() My 1989 5.0 is up on ramps right now and has been for two days now. Your second time at it is how it has been suggested to me. Any other tips and/or suggestions?
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Dropping in a new engine.... | 94GTConv | Modular Madness | 3 | 10-14-2002 04:13 PM |
Dropping fuel pressure | Rebel79 | Windsor Power | 0 | 10-29-2001 01:57 PM |
Dropping Motor this weekend have some ?s | Maxi 5.0 | Windsor Power | 1 | 08-08-2001 11:13 PM |
Fords dropping the T-45! | Mercury | Modular Madness | 2 | 05-17-2001 12:31 AM |
Dropping a 302 in the 98 V6 | Brett_C | Small Ponies | 1 | 04-03-1999 10:27 PM |