![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Addict
Join Date: Nov 2003
Location: chicopee, Ma.
Posts: 82
|
![]() my '03 GT's suspension needs to be stiffened and lowered a little bit. everything involving the suspension is stock so far. i have done a little research on springs, but i need some opinions. i've looked at steeda as the obvious and eibach so far. i dont need my suspension to be ultra firm, its an everyday summer driver on crappy new england roads, and dont want it lowered anymore than 1.5 inches. also, upper and lower control arms ... are they needed or recommended? dont want to spend too much, but quality is a must. thanks for any advice
__________________
'01 Roush Stage 3 |
![]() |
![]() |
![]() |
#2 |
Mustang Addict
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
|
![]() H&R Sport springs should be perfect for what you want.
http://www.maximummotorsports.com/HRsprings.asp
__________________
Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Dec 1999
Location: Warrington, PA
Posts: 694
|
![]() I like Eibach's progressive rate springs paired with Bilstein shocks for area's with bad roads.
I live in PA who has something like the 3rd worse roads in the country and the Eibach/Bilstein combo I had in my old '97 T-bird proved incredibly compliant on the rough surfaces, but still bit HARD into the corners. The IRS somewhat helped retain a smooth ride, but I don't think Mustang would be too far off. In fact, the combo was so nice that my brother is going to install the same into his '99 GT, and this T-bird I now own is going to get the same.
__________________
'97 T-bird LX 4.6L 2V, auto SVO heads/intake, Vortech T-trim, front mounted intercooler, blower cams, Cobra crank, Manley H-beam rods, JE pistons, Aeromotive fuel system w/ 42# injectors, and much more No times yet |
![]() |
![]() |
![]() |
#4 |
Addict
Join Date: Nov 2003
Location: chicopee, Ma.
Posts: 82
|
![]() i did some research and found the bilstein shocks to be a bit more than i would like to pay, but sounds like it would be perfect for what i want to do. i've heard nothing but good things about eibach. i've actually never heard of h&r, but the price is right and they sound like good quality. i'll continue some research on them however. thanks for the information
__________________
'01 Roush Stage 3 |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Dec 1999
Location: Warrington, PA
Posts: 694
|
![]() H&R is very good quality.
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
stocks springs vs. lowering springs | GhettoPop | Windsor Power | 1 | 02-12-2004 07:08 PM |
can I use hardtop springs in my vert? | tireburner163 | Windsor Power | 5 | 02-25-2003 02:46 PM |
H&R springs or Eibach?? (replaing my Jamex Springs) | KB94GT | Modular Madness | 0 | 05-14-2002 07:44 PM |
valve springs....questions | Old Guy with 87 GT | Windsor Power | 5 | 05-03-2002 06:36 AM |
Springs | MDM | Windsor Power | 0 | 04-11-2001 06:53 PM |