wtf is wrong now??

Fostang · 12-04-2001, 05:28 PM

I don't notice it unless i'm parked. When I start to rev the engine higher and higher i begin to hear detonations or misfires? I haven't changed the timing for a while. The engine will start to climb on the rpms just fine very smooth and when it hits about 1900-2000 rpms the misfire/detonation starts. I drop the rpms and they stop move it up again and they start all over. It won't matter if I'm running 87 or 91 octane. Sometimes they get so bad that they shake the car. The timing is set at 12 degrees. With total at 38 degrees. What can this be? This is a carburated 302 by the way. Help guys!

Mr 5 0 · 12-04-2001, 05:37 PM

First thing I'd do is check the plug wires for proper routing (the right wire on right plug) and be sure there are no crossed wires arcing or otherwise shorting out.
May not be the solution but it's a start.

7000rpmisheaven · 12-05-2001, 10:33 AM

When I put on my intake I messed something up and it didn't seal right. When I ran it, it did exactly like you were saying. I took the intake off and tryed it again. I got it right and it stopped. This may not even apply to you but its something else.

DRASTiK · 12-05-2001, 06:17 PM

When was the last time you did an ALL OUT tune-up?

Fostang · 12-05-2001, 08:28 PM

I tear down my engine about twice a year last time I did was august 8th. The plugs look fine. I'm running 8.8 accel wires with the modern wide cap. Also the petronix ignition. I checked to see if the wires were ruted correctly checked out fine. Plugs are clean but I'm going to be replacing them soon for the n20. I just want to get rid of this missing before I spray. The only thing I could see that had something wrong with it was the cap and rotor. I haven't checked to see if any of the wires are arcing yet. Started to rain and didn't stop intil a few minutes ago. How do you guys recomend I check for arcing wires?

mustangman65_79 · 12-06-2001, 07:09 AM

The way I find out, is to grab them while the car is running, it hurts, but it works.(maybe that what is wrong with me?!?!?!?!)How many miles on the car, my '66 needs a new timing chain and it does what u are talking about. My Bronco did it and all it was, was the cap and rotor, check this first.

Fostang · 12-06-2001, 04:00 PM

Well at last sunshine! Checked out the wires no arcing. Played a little with the cap and rotor cleaned them off and tried setting the rotor a little higher. Worked to a certain degree. So I'm thinking that I should replace it and see what happens.

Well its been about 3 years since the bottom end was redone mileage wise it has 6000 miles on the engine. The timing chain and cam have half that. If you do replace the timing chain I recomend a double roller.

PKRWUD · 12-08-2001, 06:44 AM

Replace the cap and rotor, and make sure the plug wires are not touching each other anywhere beyond the cap. If this doesn't solve it, you may have excessive carbon built up on the pistons, which can be cleaned with water. If you aren't familiar with this, email me and I'll walk you through it.

pkrwuds@pacbell.net

Take care,
-Chris

mustangman65_79 · 12-13-2001, 04:33 AM

I was thinking of putting a timming chain(quite one).

12-04-2001, 05:28 PM	#1
Fostang Registered Member Join Date: Feb 2001 Location: Stockton, Ca Posts: 599	wtf is wrong now?? I don't notice it unless i'm parked. When I start to rev the engine higher and higher i begin to hear detonations or misfires? I haven't changed the timing for a while. The engine will start to climb on the rpms just fine very smooth and when it hits about 1900-2000 rpms the misfire/detonation starts. I drop the rpms and they stop move it up again and they start all over. It won't matter if I'm running 87 or 91 octane. Sometimes they get so bad that they shake the car. The timing is set at 12 degrees. With total at 38 degrees. What can this be? This is a carburated 302 by the way. Help guys! __________________ 67' Fastback-Supercharged 4.6 DOHC Cobra, T-56, 8.8 more to come. 67' Coupe-EFI, AOD, 8.8 90 Gt-Supercharged,MAF,TB,1.7's ripper, bassani x, 3.55's, 01' cobras, headers. 89'GT-Supercharged,Heads,Cam,Intake,TB,MAF,power pipe,headers,offroad exhaust,black bullits.

12-05-2001, 10:33 AM	#3
7000rpmisheaven Registered Member Join Date: Nov 2001 Location: germantown MD Posts: 283	may not help either When I put on my intake I messed something up and it didn't seal right. When I ran it, it did exactly like you were saying. I took the intake off and tryed it again. I got it right and it stopped. This may not even apply to you but its something else. __________________ 85 GT 4bbl roller cam 2 ch. Flowmasters, O/R H-pipe Performer intake and carb milodon water pump, FMS 9mm wires, aluminum driveshaft, king cobra clutch

12-05-2001, 08:28 PM	#5
Fostang Registered Member Join Date: Feb 2001 Location: Stockton, Ca Posts: 599	I tear down my engine about twice a year last time I did was august 8th. The plugs look fine. I'm running 8.8 accel wires with the modern wide cap. Also the petronix ignition. I checked to see if the wires were ruted correctly checked out fine. Plugs are clean but I'm going to be replacing them soon for the n20. I just want to get rid of this missing before I spray. The only thing I could see that had something wrong with it was the cap and rotor. I haven't checked to see if any of the wires are arcing yet. Started to rain and didn't stop intil a few minutes ago. How do you guys recomend I check for arcing wires? __________________ 67' Fastback-Supercharged 4.6 DOHC Cobra, T-56, 8.8 more to come. 67' Coupe-EFI, AOD, 8.8 90 Gt-Supercharged,MAF,TB,1.7's ripper, bassani x, 3.55's, 01' cobras, headers. 89'GT-Supercharged,Heads,Cam,Intake,TB,MAF,power pipe,headers,offroad exhaust,black bullits.

12-06-2001, 07:09 AM	#6
mustangman65_79 My poor 79 RIP Join Date: Oct 2001 Location: Suisun City, Posts: 2,320	The way I find out, is to grab them while the car is running, it hurts, but it works.(maybe that what is wrong with me?!?!?!?!)How many miles on the car, my '66 needs a new timing chain and it does what u are talking about. My Bronco did it and all it was, was the cap and rotor, check this first. __________________ '84 mustang GT turbo '85 LTD '89 Camaro Irocz z28 '94 Lightning '96 Trans am

12-06-2001, 04:00 PM	#7
Fostang Registered Member Join Date: Feb 2001 Location: Stockton, Ca Posts: 599	Well at last sunshine! Checked out the wires no arcing. Played a little with the cap and rotor cleaned them off and tried setting the rotor a little higher. Worked to a certain degree. So I'm thinking that I should replace it and see what happens. Well its been about 3 years since the bottom end was redone mileage wise it has 6000 miles on the engine. The timing chain and cam have half that. If you do replace the timing chain I recomend a double roller. __________________ 67' Fastback-Supercharged 4.6 DOHC Cobra, T-56, 8.8 more to come. 67' Coupe-EFI, AOD, 8.8 90 Gt-Supercharged,MAF,TB,1.7's ripper, bassani x, 3.55's, 01' cobras, headers. 89'GT-Supercharged,Heads,Cam,Intake,TB,MAF,power pipe,headers,offroad exhaust,black bullits.

12-04-2001, 05:37 PM	#2
Mr 5 0 Conservative Individualist Join Date: May 1997 Location: Wherever I need to be Posts: 7,487	First thing I'd do is check the plug wires for proper routing (the right wire on right plug) and be sure there are no crossed wires arcing or otherwise shorting out. May not be the solution but it's a start.

12-05-2001, 06:17 PM	#4
DRASTiK Registered Member Join Date: May 2001 Location: Yuma, AZ Posts: 536	When was the last time you did an ALL OUT tune-up?

12-08-2001, 06:44 AM	#8
PKRWUD Junior Member Join Date: Mar 1999 Location: Ventura, California Posts: 8,981	Replace the cap and rotor, and make sure the plug wires are not touching each other anywhere beyond the cap. If this doesn't solve it, you may have excessive carbon built up on the pistons, which can be cleaned with water. If you aren't familiar with this, email me and I'll walk you through it. pkrwuds@pacbell.net Take care, -Chris __________________ Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local RED & WHITE!

12-13-2001, 04:33 AM	#9
mustangman65_79 My poor 79 RIP Join Date: Oct 2001 Location: Suisun City, Posts: 2,320	I was thinking of putting a timming chain(quite one). __________________ '84 mustang GT turbo '85 LTD '89 Camaro Irocz z28 '94 Lightning '96 Trans am

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
whats wrong	TMASTER	Windsor Power	16	06-10-2003 10:12 AM
new rear now MPH is wrong	fordkid68	Classic Mustangs	8	07-30-2002 12:51 PM
Wrong Balance - HOW Evident ?????	gp001	Windsor Power	2	02-28-2002 05:38 PM
A beautiful day gone wrong (accident)	1969Mach1	Blue Oval Lounge	12	12-07-2001 04:23 PM
Is This Wrong to do?	RedLilPony	Blue Oval Lounge	15	05-02-2001 01:02 AM