K-Member install ?

88workcar · 09-16-2003, 05:21 AM

Got it in yesterday! D&D kit, fine looking pieces. The option to set the motor back, do I have to cut the drive shaft or any thing? If I have to move the tranny X bar thats nothing, but the drive shaft I would need to send out.

QuantumMotorsports · 09-16-2003, 12:04 PM

If I remember right, you can set it back about an inch, and if so, yes you would have to both modify the tranny mount and the driveshaft. I would set it up normal. Just me though. Good luck.

88workcar · 09-22-2003, 05:41 AM

Got all the old stuff out yesterday, MY GOD that stuff is heavy. I will be going in with the new today.

QuantumMotorsports · 09-22-2003, 11:30 AM

Yeah man, that old K member is heavy. Be sure and post some picks when you're done!

09-16-2003, 05:21 AM	#1
88workcar Registered Member Join Date: Oct 1999 Location: Pierre Part, La. U.S.A. Posts: 1,850	K-Member install ? Got it in yesterday! D&D kit, fine looking pieces. The option to set the motor back, do I have to cut the drive shaft or any thing? If I have to move the tranny X bar thats nothing, but the drive shaft I would need to send out. __________________ 88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid I'm somewhere in tthe middle.

09-16-2003, 12:04 PM	#2
QuantumMotorsports Registered Member Join Date: Jul 2000 Location: Norman, Oklahoma, USA Posts: 597	If I remember right, you can set it back about an inch, and if so, yes you would have to both modify the tranny mount and the driveshaft. I would set it up normal. Just me though. Good luck. __________________ Michael Black QuantumMotorsports Norman, OK 1984 LX Hatch 306 w/ TRW forged flat toppers, Comp Cams Magnum 292H, GT40P heads w/ 3 angle valve job, .550 lift springs, Angus Racing Roller Rockers, Weiand Stealth Intake, Holley 4150 650cfm carb, MAC 1 5/8 Long Tubes, Single Chamber Flowmasters, 91' T5 w/ Pro 5.0 shifter, Turbo Coupe 8.8 Rear w/ 3.55 gears, QA1 Motorsports tubular K member, no interior except steering wheel and seat. Coming soon: 6 or 8 point cage, Fuel Cell, Weld Draglites

09-22-2003, 05:41 AM	#3
88workcar Registered Member Join Date: Oct 1999 Location: Pierre Part, La. U.S.A. Posts: 1,850	Got all the old stuff out yesterday, MY GOD that stuff is heavy. I will be going in with the new today. __________________ 88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid I'm somewhere in tthe middle.

09-22-2003, 11:30 AM	#4
QuantumMotorsports Registered Member Join Date: Jul 2000 Location: Norman, Oklahoma, USA Posts: 597	Yeah man, that old K member is heavy. Be sure and post some picks when you're done! __________________ Michael Black QuantumMotorsports Norman, OK 1984 LX Hatch 306 w/ TRW forged flat toppers, Comp Cams Magnum 292H, GT40P heads w/ 3 angle valve job, .550 lift springs, Angus Racing Roller Rockers, Weiand Stealth Intake, Holley 4150 650cfm carb, MAC 1 5/8 Long Tubes, Single Chamber Flowmasters, 91' T5 w/ Pro 5.0 shifter, Turbo Coupe 8.8 Rear w/ 3.55 gears, QA1 Motorsports tubular K member, no interior except steering wheel and seat. Coming soon: 6 or 8 point cage, Fuel Cell, Weld Draglites

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Gears, Install, and Questions	B2r3y	Windsor Power	6	02-21-2003 05:00 PM
Ring and Pinion Install	Titan	Modular Madness	21	08-15-2002 10:06 PM
A Question for 94-95 owners concerning 1.7RR INSTALL	SlowStang2	Windsor Power	6	09-22-2001 06:39 PM