toploader for sale

BoJangles · 09-23-2004, 08:21 PM

I have a top loader out of a 65 mustang, the car was wrecked in 1967 the transmission was installed behind a 260 falcoln for several years was taken out about 1974 and hasn't been behind an engine sence then. All the gears are factory and are extremly low millage, I have had this transmission sence I bought it in 1967. It still shifts like a dream. Has original mustang shifter, but needs a new handle, 1 joke in excilent condition and another just for keeping it clean. The drive shaft that the other joke is attached is out of a 1969 Torino. Asking $1000 for all of it.

mustangII460 · 09-26-2004, 10:34 PM

#1 Please fill in your location.

#2 Does it have a ID tag. If so, what is the number?

#3 Is a wide ratio, or close ratio. Count teeth on the second gear. 28 is wide, 31 close.

#4 Is the case 24, 25.5 or 27 inches long.

#5 How many spline are on the input shaft.

#6 Bell housing?

Reason I ask is there is about 37 different types of loaders.

BoJangles · 10-09-2004, 05:46 PM

1. done
2. yes it has an ID tag: RUG E 016830
3. wide
4. 24 inches
5. 10 splines
6. no bellhousing

sorry i've been out and hadn't had a chance to reply to this post

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
T-5 or Toploader 4- Speed	j's69stang	Classic Mustangs	5	01-23-2008 02:33 AM
Toploader 4 speed VS FMX auto	Metal396	Classic Mustangs	6	03-16-2003 10:00 AM
Toploader 4spd conversion?	brooksgnm	Windsor Power	4	11-04-2002 10:48 PM
toploader 4 speed?	Lightspeed	Classic Mustangs	3	07-19-2002 10:12 PM
4 speed toploader with Hurst Linkage	gofishing	Classic Mustangs	1	10-27-1999 10:52 PM

09-23-2004, 08:21 PM	#1
BoJangles Registered Member Join Date: Sep 2004 Location: silsbee, TX, about 20 miles north of Beaumont Posts: 2	toploader for sale I have a top loader out of a 65 mustang, the car was wrecked in 1967 the transmission was installed behind a 260 falcoln for several years was taken out about 1974 and hasn't been behind an engine sence then. All the gears are factory and are extremly low millage, I have had this transmission sence I bought it in 1967. It still shifts like a dream. Has original mustang shifter, but needs a new handle, 1 joke in excilent condition and another just for keeping it clean. The drive shaft that the other joke is attached is out of a 1969 Torino. Asking $1000 for all of it.

09-26-2004, 10:34 PM	#2
mustangII460 Factoy Five Roadster Join Date: May 2000 Location: Sevier Co,Tennessee Posts: 1,681	#1 Please fill in your location. #2 Does it have a ID tag. If so, what is the number? #3 Is a wide ratio, or close ratio. Count teeth on the second gear. 28 is wide, 31 close. #4 Is the case 24, 25.5 or 27 inches long. #5 How many spline are on the input shaft. #6 Bell housing? Reason I ask is there is about 37 different types of loaders. __________________ Frank

10-09-2004, 05:46 PM	#3
BoJangles Registered Member Join Date: Sep 2004 Location: silsbee, TX, about 20 miles north of Beaumont Posts: 2	1. done 2. yes it has an ID tag: RUG E 016830 3. wide 4. 24 inches 5. 10 splines 6. no bellhousing sorry i've been out and hadn't had a chance to reply to this post