How accurate is that analyzer?

Killercanary · 03-13-2001, 11:37 PM

I knew my exact weight and MPH on a pass once, and now I run dead on- actually my ET is a little better than projected by the analyzer. It says I have roughly 270HP (and i too think these are flywheel numbers, not rear wheel) and a guy that has the same setup as me dyno'd 235rwhp, which is about 270FWHP. I dyno'd 188rwhp in 3rd gear on a mustang chassis dyno, but corrected from my torque graph and 1:1 ratio in 4th, it turned out that I should have also had 235rwhp. I think they are a good thing to give you an idea as to where you might be. I never thought that the projected times and MPH it stated were unobtainable, but with traction and good driving I have matched them like I said.

------------------
95 GT convt' 5 speed, 3.73's,FMS HD clutch, Pro 5.0 shifter, ASP alum. underdrive pulleys, Bassani offroad X pipe, 2 chmbr flowmasters, K&N w/o silencer, edelbrock performer intake, FRPP 65mm T-body, FRPP shorty headers, FRPP aluminum driveshaft.Hooker 4pt chrome car bar, Xenon/Wings West ground effects, custom interior
Best ET: 13.83
Best MPH: 98.55mph with Best 60': 1.91 on Nitto DR's
Homepage: <A HREF="http://www.angelfire.com/pa2/killercanary" TARGET=_blank>http://www.angelfire

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Switch to Hybrid Mode Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
how accurate?	sn95gt19	Windsor Power	0	04-03-2003 07:52 PM
MW Analyzer	sn94gt	Windsor Power	0	02-19-2003 10:20 AM
HP? Regarding Analyzer	geno5.0	Stang Stories	11	04-18-2002 11:25 AM
'Stang Analyzer Questions.....	bigwhitecobra	Blue Oval Lounge	2	08-26-2001 08:21 PM

03-13-2001, 11:37 PM	#5
Killercanary Registered Member Join Date: Nov 1999 Location: Altoona, PA Posts: 336	I knew my exact weight and MPH on a pass once, and now I run dead on- actually my ET is a little better than projected by the analyzer. It says I have roughly 270HP (and i too think these are flywheel numbers, not rear wheel) and a guy that has the same setup as me dyno'd 235rwhp, which is about 270FWHP. I dyno'd 188rwhp in 3rd gear on a mustang chassis dyno, but corrected from my torque graph and 1:1 ratio in 4th, it turned out that I should have also had 235rwhp. I think they are a good thing to give you an idea as to where you might be. I never thought that the projected times and MPH it stated were unobtainable, but with traction and good driving I have matched them like I said. ------------------ 95 GT convt' 5 speed, 3.73's,FMS HD clutch, Pro 5.0 shifter, ASP alum. underdrive pulleys, Bassani offroad X pipe, 2 chmbr flowmasters, K&N w/o silencer, edelbrock performer intake, FRPP 65mm T-body, FRPP shorty headers, FRPP aluminum driveshaft.Hooker 4pt chrome car bar, Xenon/Wings West ground effects, custom interior Best ET: 13.83 Best MPH: 98.55mph with Best 60': 1.91 on Nitto DR's Homepage: <A HREF="http://www.angelfire.com/pa2/killercanary" TARGET=_blank>http://www.angelfire