Is it a good cam for me???

riceboyskiller · 01-20-2002, 01:46 AM

My local speed shop wants to sell me this following camshaft

SPEED PRO # CS-195R 212-222 A .050 ET .493/.510 LIFT

I don't know anythings about this stick

My engine is basically stock with lightly ported ETE with upgrade springs, trick flow street intake, 1 5/8 headers with 2 1/2 exhaust and 8-9 psi from a powerdyne.

For my me it sounds really good, but for you master-stangbangers, is it so good????

Tanx

Five0 · 01-20-2002, 04:57 AM

Sounds like a good cam, not too big not too small.

riceboyskiller · 01-20-2002, 07:05 AM

Tanx a lot Fiveo

You're Stang is just like mine...a black coupe!!

I want to know wath is your rear and front rim size(tire size too)

Look very mean

Five0 · 01-21-2002, 06:52 AM

I am not too sure what the rim size is because I bought the car with the rims on it already.

I think they are 15/8 and 15/5 with 5 inch back spacing but I am not sure.

LittleBlueStang · 01-21-2002, 08:12 AM

In your particular application, because you are running boost, you really need to look at the cams duration. Because of it's nature, the blower exaggerates every performance mod that you do as well as any shortcomings in your combo. The duration shouldn't be too much over about 230ish in degrees for your particular setup. Too much duration would cause the valves to hang open too long and wouldn't help you optimize power output. Hope this info was helpful. Hey FiveO, nice ride!

riceboyskiller · 01-21-2002, 12:40 PM

So Littleblue stang do you think this cam is good for my engine. I know the stock heads really sucks but in the near furture i will buy a set of good aluminium head

Five0 · 01-21-2002, 09:11 PM

Thanks!

Mach 1 · 01-21-2002, 11:00 PM

Yes, thats a good cam for you. go for it.

LittleBlueStang · 01-22-2002, 11:58 AM

Anything that will help your car breath will pay big dividends. Aluminum heads will really help because they have a better heat coefficient than cast iron and allow for a slightly higher compression ratio. Good ported aluminum heads and a ported aftermarket intake would be a huge help. Also a good set of headers (jet-hot coated?) and look into a good throttle body/injector setup. I've heard of guys running in the 11's w/ a good blower/intake/head selection on the stock cam so I know that if you concentrate on the breathing of the car, 11's would be gravy.

jonnyk · 01-22-2002, 12:13 PM

What's the lobe separation angle on that cam? With a blower it's nicer to run 112° or 114° so you don't blow boost out the exhaust side (overlap = bad). Also provides for a broader powerband.

Strim91GT · 01-22-2002, 02:08 PM

I was about to say..... lobe seperation is pretty important with a blower. You want something that has pretty decent lobe seperation. just like jonnyk said, something with 112-114 degrees. You don't want to be throwing away the boost your blower makes by pushing it out the exhaust.

Mach 1 · 01-22-2002, 02:27 PM

just about every mustang cam out there has a 112 LSA. Some are 114, a few are 110.

with a blower, i would recommend 114, although many people run blowers with 110 and 112 with good results.

riceboyskiller · 01-22-2002, 05:31 PM

I don't know about the LSA of the cam. I will ask him tonite and come back with it in a near futur.

Tanx a lot guyz to pay attention to a poor french guy

riceboyskiller · 01-23-2002, 08:03 AM

I 've got it...my speed pro cam have 112 LSA and 60 overlap.

So it's good ????????????

Eric4Nitrous · 01-23-2002, 08:18 AM

Hey, sounds like a good cam. But if I were you, I would go with the F303 Cam. My mom (yes my mom) lol has a 95 Gt with a stock block. All it has is the F303, Shorty Headers, H-pipe, flowmasters, gears, and a Powerdyne 6lb. The car Pulls like a HORSE. The F303 is one of the best cams out there in my opinion. You might want to try it. Lift is .512 so you'll be plenty safe.

Eric

Mach 1 · 01-23-2002, 03:51 PM

Your mom rocks!

01-20-2002, 01:46 AM	#1
riceboyskiller Registered Member Join Date: Sep 2001 Location: sherbrooke,quebec,canada Posts: 46	Is it a good cam for me??? My local speed shop wants to sell me this following camshaft SPEED PRO # CS-195R 212-222 A .050 ET .493/.510 LIFT I don't know anythings about this stick My engine is basically stock with lightly ported ETE with upgrade springs, trick flow street intake, 1 5/8 headers with 2 1/2 exhaust and 8-9 psi from a powerdyne. For my me it sounds really good, but for you master-stangbangers, is it so good???? Tanx __________________ 92 black LX

01-20-2002, 04:57 AM	#2
Five0 Registered Member Join Date: Apr 2000 Location: middleburg, fl, usa Posts: 1,134	Sounds like a good cam, not too big not too small. __________________ James Cox RHC Member #44 nochevy@hotmail.com 1991 Mustang LX Dart iron eagle block, 4340 28oz 347 crank, 4340 h-beam rods, probe ultra light pistons canfield heads “race ported by Brent Frazier”, solid roller cam and lifters “custom grind”, kooks 1 7/8" race headers, and much more. Engine built by Brent Frazier.

01-20-2002, 07:05 AM	#3
riceboyskiller Registered Member Join Date: Sep 2001 Location: sherbrooke,quebec,canada Posts: 46	Tanx a lot Fiveo You're Stang is just like mine...a black coupe!! I want to know wath is your rear and front rim size(tire size too) Look very mean __________________ 92 black LX

01-21-2002, 06:52 AM	#4
Five0 Registered Member Join Date: Apr 2000 Location: middleburg, fl, usa Posts: 1,134	I am not too sure what the rim size is because I bought the car with the rims on it already. I think they are 15/8 and 15/5 with 5 inch back spacing but I am not sure. __________________ James Cox RHC Member #44 nochevy@hotmail.com 1991 Mustang LX Dart iron eagle block, 4340 28oz 347 crank, 4340 h-beam rods, probe ultra light pistons canfield heads “race ported by Brent Frazier”, solid roller cam and lifters “custom grind”, kooks 1 7/8" race headers, and much more. Engine built by Brent Frazier.

01-21-2002, 08:12 AM	#5
LittleBlueStang Registered Member Join Date: Dec 2001 Location: Augusta, MI Posts: 24	In your particular application, because you are running boost, you really need to look at the cams duration. Because of it's nature, the blower exaggerates every performance mod that you do as well as any shortcomings in your combo. The duration shouldn't be too much over about 230ish in degrees for your particular setup. Too much duration would cause the valves to hang open too long and wouldn't help you optimize power output. Hope this info was helpful. Hey FiveO, nice ride! __________________ sleepers have more fun (That's a stock intake, really.)

01-21-2002, 12:40 PM	#6
riceboyskiller Registered Member Join Date: Sep 2001 Location: sherbrooke,quebec,canada Posts: 46	So Littleblue stang do you think this cam is good for my engine. I know the stock heads really sucks but in the near furture i will buy a set of good aluminium head __________________ 92 black LX

01-21-2002, 09:11 PM	#7
Five0 Registered Member Join Date: Apr 2000 Location: middleburg, fl, usa Posts: 1,134	Thanks! __________________ James Cox RHC Member #44 nochevy@hotmail.com 1991 Mustang LX Dart iron eagle block, 4340 28oz 347 crank, 4340 h-beam rods, probe ultra light pistons canfield heads “race ported by Brent Frazier”, solid roller cam and lifters “custom grind”, kooks 1 7/8" race headers, and much more. Engine built by Brent Frazier.

01-21-2002, 11:00 PM	#8
Mach 1 Registered Member Join Date: May 1999 Location: Georgia Posts: 3,866	Yes, thats a good cam for you. go for it. __________________ 2002 GT 1993 GT (SOLD) '93 Mustang GT RHC member #142

01-22-2002, 11:58 AM	#9
LittleBlueStang Registered Member Join Date: Dec 2001 Location: Augusta, MI Posts: 24	Anything that will help your car breath will pay big dividends. Aluminum heads will really help because they have a better heat coefficient than cast iron and allow for a slightly higher compression ratio. Good ported aluminum heads and a ported aftermarket intake would be a huge help. Also a good set of headers (jet-hot coated?) and look into a good throttle body/injector setup. I've heard of guys running in the 11's w/ a good blower/intake/head selection on the stock cam so I know that if you concentrate on the breathing of the car, 11's would be gravy. __________________ sleepers have more fun (That's a stock intake, really.)

01-22-2002, 12:13 PM	#10
jonnyk Being stroked is great Join Date: Oct 1998 Location: Alberta, Canada Posts: 772	What's the lobe separation angle on that cam? With a blower it's nicer to run 112° or 114° so you don't blow boost out the exhaust side (overlap = bad). Also provides for a broader powerband. __________________ Novi 2000 now spinning off the snout of the 331... Mods Pics

01-22-2002, 02:08 PM	#11
Strim91GT Registered Member Join Date: Jan 2001 Location: Kansas Posts: 59	I was about to say..... lobe seperation is pretty important with a blower. You want something that has pretty decent lobe seperation. just like jonnyk said, something with 112-114 degrees. You don't want to be throwing away the boost your blower makes by pushing it out the exhaust. __________________ vortech s trim,edelbrock 6032's, b303, cobra intake, 70mm tb, pro m 75mm bullet, granatelli alum. rad., accel 330+ digital ign., msd boost tim. ret., 30# inj., 190 lph fuel pump, t-rex pump, bbk, press. reg., tremec tko, ram billet flywheel, dual friction clutch, pro 5.0 shifter, 4.10 gears, aluminum quadrant, motorsport alum. driveshaft, hooker headers, off road h pipe, flowmaster cat back, subframes, megabyte jr lowers, heavy duty uppers, eibach springs drag springs, koni sport shocks, polished cobra r's, 85-86 taillights, msd pro billet distributor

01-22-2002, 02:27 PM	#12
Mach 1 Registered Member Join Date: May 1999 Location: Georgia Posts: 3,866	just about every mustang cam out there has a 112 LSA. Some are 114, a few are 110. with a blower, i would recommend 114, although many people run blowers with 110 and 112 with good results. __________________ 2002 GT 1993 GT (SOLD) '93 Mustang GT RHC member #142

01-22-2002, 05:31 PM	#13
riceboyskiller Registered Member Join Date: Sep 2001 Location: sherbrooke,quebec,canada Posts: 46	I don't know about the LSA of the cam. I will ask him tonite and come back with it in a near futur. Tanx a lot guyz to pay attention to a poor french guy __________________ 92 black LX

01-23-2002, 08:03 AM	#14
riceboyskiller Registered Member Join Date: Sep 2001 Location: sherbrooke,quebec,canada Posts: 46	I 've got it...my speed pro cam have 112 LSA and 60 overlap. So it's good ???????????? __________________ 92 black LX

01-23-2002, 08:18 AM	#15
Eric4Nitrous Registered Member Join Date: Jan 2002 Location: Va Posts: 1,122	Hey, sounds like a good cam. But if I were you, I would go with the F303 Cam. My mom (yes my mom) lol has a 95 Gt with a stock block. All it has is the F303, Shorty Headers, H-pipe, flowmasters, gears, and a Powerdyne 6lb. The car Pulls like a HORSE. The F303 is one of the best cams out there in my opinion. You might want to try it. Lift is .512 so you'll be plenty safe. Eric __________________ 68 Camaro Gene Fulton 632ci Two stages of Jug 8.41 164mph Rockingham 1-26-03

01-23-2002, 03:51 PM	#16
Mach 1 Registered Member Join Date: May 1999 Location: Georgia Posts: 3,866	Your mom rocks! __________________ 2002 GT 1993 GT (SOLD) '93 Mustang GT RHC member #142

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Lynyrd Skynyrd	mustang2002	Blue Oval Lounge	48	07-05-2002 08:44 PM
Good Car Movies?	1969Mach1	Blue Oval Lounge	22	05-21-2002 08:56 AM
Track Last Night!! (Good and Terrible)	CobraConv99	Stang Stories	6	11-09-2001 12:59 AM
Good race with a new V6 stang...	Skyman	Stang Stories	6	01-01-2001 06:06 PM