Intake Manifold ?'s

Tbird8450 · 04-17-2001, 12:08 PM

I have a basically stock 5.0 GT. There has been no work done to the engine as of yet. My friend wants to sell me a Downs Ford ported and polished GT40 upper and lower intake. I was just wondering how it would perform on my car given its current state. The heads, mass air, exhaust, throttle body, etc are all stock. With that considered, will I notice a difference in power? If so, how much? How will the power be both in low end and in the top end? Any insite would be appreciated. Thanks.

302 LX Eric · 04-17-2001, 12:17 PM

On your stock motor, a ported and polished GT40 intake isn't really going to help you that much. You basically still have "bottlenecks" in your motor (i.e. TB, heads, small valve size, exhaust, etc.)

Plus, since the intake is ported and polished, it would probably work better on a more modified 5.0.

If the price is low, and you plan on making head, TB, exhaust upgrades in the futre, then I guess it would be a good buy.

Good luck,
E

------------------
1991 5.0 LX Coupe - 38,000 miles

13.17 @ 106.14 mph w/ 2.138 60'

Tbird8450 · 04-17-2001, 12:22 PM

I basically want to make sure that I won't lose any power. I need to replace the intake manifold and valve cover gaskets anyway, so I figured that I might as well throw this on while everything is taken apart. Eventually I'll have heads, exhaust, TB, and all of that other good stuff.

He paid about $800 for it new. It's still in great shape, and he'll sell it to me for $350. Good deal?

04-17-2001, 04:34 PM

I wouldn't make that mod alone. If you can I'd group the intake together w/ the MAF, TB (otherwise you'll be starving the intake). If the price is right, tough, it's always worth it, and you'll have extra $$$ for these other things. I don't think doing it alone will hurt you any, but I also don't think it'll help you much either. The increases will be minimal unless you group it together with similar functioning grouped parts (intake system, fuel, exhaust).

------------------
'90 LX 5.0; 12K original miles (no sh*&); 3.55 gears; pulleys;Edelbrock Performer Heads; BBK shorties; MSD 6AL box w/ blaster 2 coil; Motorsport E303 cam; Pro-M 75mm MAF; BBK 70mm TB; Eibach spring kit; Southside sub-connectors; K&N cone filter charger; Hurst shifter; fiberglass cowl hood; A/C-less; rear seat-less; cat-less; Flomasters; Corbeau racing seats (fronts);
30# injectors; 190 lb fp FPR; TFS Twisted Wedge Intake 12.513 @ 108 mph (Pre-inj/fuelpump/FPR/ intake)

Tbird8450 · 04-18-2001, 07:38 AM

Hmm, I suppose I will go for it then. The upper is already port matched to a 75mm throttle body, so maybe I'll throw one on along with a bigger mass air meter. What size should I go with there? Thanks again.

Mach 1 · 04-18-2001, 07:46 AM

I say go for it. you might lose a small amount of low end torque, but you should pick up 5-10 horses up top.

75 mm throttle body is to big. stick with a 70 or 65mm. it wont hurt if the upper intake opening is bigger than the TB. And i would go with a pro-m bullet 75mm MAF meter.

------------------
1993 GT/AOD
'93 Mustang GT

04-18-2001, 01:23 PM

I agree w/ Mach 1.....the 75 TB is way too big. Remember you're MAF has to stay larger than the TB....so if you got the 75 TB, you're looking at an 80 MAF. I'd stick w/ a 75 MAF and 65-70 TB.

------------------
'90 LX 5.0; 12K original miles (no sh*&); 3.55 gears; pulleys;Edelbrock Performer Heads; BBK shorties; MSD 6AL box w/ blaster 2 coil; Motorsport E303 cam; Pro-M 75mm MAF; BBK 70mm TB; Eibach spring kit; Southside welded subs; K&N cone filter charger; Hurst shifter; fiberglass turbo hood; A/C-less; rear seat-less; cat-less; 2 chamber Flos; Corbeau racing seats (fronts);
30# injectors; 190 lb fp; FPR; TFS track heat Intake - 12.513 @ 112 mph (Pre-inj/fuelpump/FPR/intake)

04-17-2001, 12:08 PM	#1
Tbird8450 Registered Member Join Date: May 1999 Location: PA Posts: 124	Intake Manifold ?'s I have a basically stock 5.0 GT. There has been no work done to the engine as of yet. My friend wants to sell me a Downs Ford ported and polished GT40 upper and lower intake. I was just wondering how it would perform on my car given its current state. The heads, mass air, exhaust, throttle body, etc are all stock. With that considered, will I notice a difference in power? If so, how much? How will the power be both in low end and in the top end? Any insite would be appreciated. Thanks.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
TFS Intake manifold	Hozer 88GTConv	Windsor Power	1	10-15-2004 03:47 PM
intake manifold cracked on my 97 GT-help!	jinx6570	Modular Madness	4	12-23-2002 03:28 AM
help with intake manifold...	71grande	Classic Mustangs	11	11-20-2002 11:29 PM
Power Gains w/ new intake manifold???	Blaster	Windsor Power	2	10-14-2001 01:59 AM
intake manifold selection	yusuf	Windsor Power	0	03-05-2001 04:07 AM

04-17-2001, 12:17 PM	#2
302 LX Eric or '331 LX Eric' Join Date: Jan 1999 Location: Columbus, Ohio Posts: 2,142	On your stock motor, a ported and polished GT40 intake isn't really going to help you that much. You basically still have "bottlenecks" in your motor (i.e. TB, heads, small valve size, exhaust, etc.) Plus, since the intake is ported and polished, it would probably work better on a more modified 5.0. If the price is low, and you plan on making head, TB, exhaust upgrades in the futre, then I guess it would be a good buy. Good luck, E ------------------ 1991 5.0 LX Coupe - 38,000 miles 13.17 @ 106.14 mph w/ 2.138 60'

04-17-2001, 12:22 PM	#3
Tbird8450 Registered Member Join Date: May 1999 Location: PA Posts: 124	I basically want to make sure that I won't lose any power. I need to replace the intake manifold and valve cover gaskets anyway, so I figured that I might as well throw this on while everything is taken apart. Eventually I'll have heads, exhaust, TB, and all of that other good stuff. He paid about $800 for it new. It's still in great shape, and he'll sell it to me for $350. Good deal?

04-17-2001, 04:34 PM	#4
1mintlx Guest Posts: n/a	I wouldn't make that mod alone. If you can I'd group the intake together w/ the MAF, TB (otherwise you'll be starving the intake). If the price is right, tough, it's always worth it, and you'll have extra $$$ for these other things. I don't think doing it alone will hurt you any, but I also don't think it'll help you much either. The increases will be minimal unless you group it together with similar functioning grouped parts (intake system, fuel, exhaust). ------------------ '90 LX 5.0; 12K original miles (no sh*&); 3.55 gears; pulleys;Edelbrock Performer Heads; BBK shorties; MSD 6AL box w/ blaster 2 coil; Motorsport E303 cam; Pro-M 75mm MAF; BBK 70mm TB; Eibach spring kit; Southside sub-connectors; K&N cone filter charger; Hurst shifter; fiberglass cowl hood; A/C-less; rear seat-less; cat-less; Flomasters; Corbeau racing seats (fronts); 30# injectors; 190 lb fp FPR; TFS Twisted Wedge Intake 12.513 @ 108 mph (Pre-inj/fuelpump/FPR/ intake)

04-18-2001, 07:38 AM	#5
Tbird8450 Registered Member Join Date: May 1999 Location: PA Posts: 124	Hmm, I suppose I will go for it then. The upper is already port matched to a 75mm throttle body, so maybe I'll throw one on along with a bigger mass air meter. What size should I go with there? Thanks again.

04-18-2001, 07:46 AM	#6
Mach 1 Registered Member Join Date: May 1999 Location: Georgia Posts: 3,866	I say go for it. you might lose a small amount of low end torque, but you should pick up 5-10 horses up top. 75 mm throttle body is to big. stick with a 70 or 65mm. it wont hurt if the upper intake opening is bigger than the TB. And i would go with a pro-m bullet 75mm MAF meter. ------------------ 1993 GT/AOD '93 Mustang GT

04-18-2001, 01:23 PM	#7
bada$$lx Guest Posts: n/a	I agree w/ Mach 1.....the 75 TB is way too big. Remember you're MAF has to stay larger than the TB....so if you got the 75 TB, you're looking at an 80 MAF. I'd stick w/ a 75 MAF and 65-70 TB. ------------------ '90 LX 5.0; 12K original miles (no sh*&); 3.55 gears; pulleys;Edelbrock Performer Heads; BBK shorties; MSD 6AL box w/ blaster 2 coil; Motorsport E303 cam; Pro-M 75mm MAF; BBK 70mm TB; Eibach spring kit; Southside welded subs; K&N cone filter charger; Hurst shifter; fiberglass turbo hood; A/C-less; rear seat-less; cat-less; 2 chamber Flos; Corbeau racing seats (fronts); 30# injectors; 190 lb fp; FPR; TFS track heat Intake - 12.513 @ 112 mph (Pre-inj/fuelpump/FPR/intake)