Depressing Dyno...

Unit 5302 · 03-29-2002, 10:58 PM

Umm... hate to point this out guys, but he's running 1.7:1 roller rockers on that B303.

.510/.510 and 224*/224* duration is more than enough cam to make plenty of top end power. There is nothing wrong with the cam. If I'm correct, the GT-40P crate engine is rated at 320hp with a B303.

You're about 30-40hp short of where you should be. 255rwhp = about 310 at the crank. You should make around 340-350 at the crank with your combo, which would be around 280-290rwhp. If you bumped the CR, switched to a 76mm MAF, a 70mm T/B, and got a different intake, you might be able to see your 340rwhp, but that's about 410 at the crank. 410hp N/A with an EFI 306 is a pretty tall call, but with 10.5:1 you might be able to pull it off.

With TFS TW heads, the last intake test I heard about had the Holley absolutely trouncing the other intakes. I would certainly recommend it for max power on your combo.

Was the Dynojet equipped with a load bearing device? If not, forget about the correction factors. They aren't whats messing with you. In fact, the dyno may not have any adjustable correction factors depending on the model.

You know you have a misfire, and obviously that's top order. Hey, exgmguy, weren't your heads older model TFS's before the change over?

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Switch to Hybrid Mode Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Darius' dyno numbers	drudis	Power Adders	7	08-27-2004 04:09 PM
Stingy Dyno?	SleeperGT	Modular Madness	4	10-22-2003 01:42 PM
My latest dyno adventures	XR1stang	Blue Oval Lounge	6	08-01-2003 04:00 PM
Dyno resource website	97mustangcobrad	Racer's Club House	0	11-08-2001 11:38 AM

03-29-2002, 10:58 PM	#28
Unit 5302 Registered Member Join Date: May 1999 Posts: 5,246	Umm... hate to point this out guys, but he's running 1.7:1 roller rockers on that B303. .510/.510 and 224/224 duration is more than enough cam to make plenty of top end power. There is nothing wrong with the cam. If I'm correct, the GT-40P crate engine is rated at 320hp with a B303. You're about 30-40hp short of where you should be. 255rwhp = about 310 at the crank. You should make around 340-350 at the crank with your combo, which would be around 280-290rwhp. If you bumped the CR, switched to a 76mm MAF, a 70mm T/B, and got a different intake, you might be able to see your 340rwhp, but that's about 410 at the crank. 410hp N/A with an EFI 306 is a pretty tall call, but with 10.5:1 you might be able to pull it off. With TFS TW heads, the last intake test I heard about had the Holley absolutely trouncing the other intakes. I would certainly recommend it for max power on your combo. Was the Dynojet equipped with a load bearing device? If not, forget about the correction factors. They aren't whats messing with you. In fact, the dyno may not have any adjustable correction factors depending on the model. You know you have a misfire, and obviously that's top order. Hey, exgmguy, weren't your heads older model TFS's before the change over?