AOD mods?

04-05-2002, 01:32 AM

Here is my experiences with this situation. If you buy an Art Carr one piece input shaft you will have to have an Art Carr converter. I have a PI solid shaft and it will work with any convertor.

Convertors.. I had a B&M holeshot(when stock) and thought it was a good unit(B&M shift kit at the time). I bought a lockup PI convertor after the engine change and was miserable. The car ran like ****. PI said it was a tuning problem but would refund my money. I sent it back and had it recalibrated to a 2800(from 3000) and non-lockup(one time free change with purchase) and added a lentech valve body at the same time(at the suggestion of lentech) and all I can say is WOW. The car is sooo much faster(seat of pants) and runs better than before. Gas mileage, slightly worst with a non-lockup?? *cough*BS*cough* I hardly drive the car lately because of the gas mileage(couple other reasons too though). Big difference in gas mileage.

I couldn't be happier with the lentech unit. I hardly ever use od around town anyhow, if you do you have/will have a problem anyhow. Using od around town will cause the od to burn out. The Lentech unit will allow you to hold any/all gears to whatever rpm you want and that makes one hell of a big difference.

Mach1, it will shift into od at full throttle after a certain speed. I like to have control of what the car is doing and I appreciate what the Lentech unit alllows me... an auto/manual tanny.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Switch to Hybrid Mode Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
What mods next?	SteveAZ	Windsor Power	0	05-20-2003 09:00 PM
Brake mods ( and other first mods) for a 98 Vert	Chevyguy	Modular Madness	11	09-19-2002 10:03 AM
Future Mods	Strider	Modular Madness	6	12-19-2001 01:39 AM
Making a fast Street Car = More mods?	MrClean	Windsor Power	15	09-11-2001 04:40 PM
New Mods! - Also, how fast will I go?	2FastLX	Windsor Power	0	03-20-2001 09:06 AM

04-05-2002, 01:32 AM	#10
rbatson Guest Posts: n/a	Here is my experiences with this situation. If you buy an Art Carr one piece input shaft you will have to have an Art Carr converter. I have a PI solid shaft and it will work with any convertor. Convertors.. I had a B&M holeshot(when stock) and thought it was a good unit(B&M shift kit at the time). I bought a lockup PI convertor after the engine change and was miserable. The car ran like **. PI said it was a tuning problem but would refund my money. I sent it back and had it recalibrated to a 2800(from 3000) and non-lockup(one time free change with purchase) and added a lentech valve body at the same time(at the suggestion of lentech) and all I can say is WOW*. The car is sooo much faster(seat of pants) and runs better than before. Gas mileage, slightly worst with a non-lockup?? coughBScough* I hardly drive the car lately because of the gas mileage(couple other reasons too though). Big difference in gas mileage. I couldn't be happier with the lentech unit. I hardly ever use od around town anyhow, if you do you have/will have a problem anyhow. Using od around town will cause the od to burn out. The Lentech unit will allow you to hold any/all gears to whatever rpm you want and that makes one hell of a big difference. Mach1, it will shift into od at full throttle after a certain speed. I like to have control of what the car is doing and I appreciate what the Lentech unit alllows me... an auto/manual tanny.