What rear end parts to buy?

NOSstang89 · 05-21-2001, 10:04 PM

The car broke a Moser forged axle last weekend at the track, so I might as well just upgrade the whole rear end so I don't break stuff back there anymore. What stuff will be happy with 5000 rpm launches with 400hp/500tq?
I was planning to upgrade to at least 31 spline axles, though I'd prefer 33 or 35. But that depends of what carrier I get... Does anyone make a strong differential that is streetable w/ 33 or 35 splines? If not, will 31's be ok? I also plan to get a rear end girdle kit and some C clip eliminators.

I need something that will be pretty good on the street, but strong enough for some hard launches. I also want something that is rebuildable so I don't have to keep buying new units when they wear out (eg., no Auburn or other gear type diffs...). Do such parts exist?

Thanks!!

------------------
'92LX hatch, 302 w/TFS Street Heats, Performer RPM intake, Crane cam .499/.510, Crower 1.6rr, 70mmTB/EGR, Pro-M 75mm Maf, SVO 30lb injectors, BBK underdrive pullies, 255lph intank pump, BBK short headers, MAC 2.5" off road X pipe, FMS King Cobra clutch, 3.73 gears, SVO upper arms, HPM Megabite Jr. lowers, Moser forged axles, lakewood driveshaft loop, air pump removed

279.1 rwhp / 303.5 rwtq N/A
395.7 rwhp / 496.5 rwtq NOS

WADS56 · 05-21-2001, 11:18 PM

I have moser 31's with a auburn diff. and a girdle. I launch between 5500 and 6000rpm and have had np problems.

------------------
347 W/ A-trim 6#'s, Canfield heads, out of the box Systemax II intake, solid roller cam. 11.1 @123mph

93lx 5.0 daily driver

LX XLR8R · 05-22-2001, 09:49 AM

yea 31 spline mosers, or strange axels with a good diff will be nearly industructable..the powertrax diff is good for 1,000hp if a cheap locker is what ur looking for

------------------
1987 black notch(ex 4 banger)
DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..
AIM=onesillynotch

IMPULSERACING · 05-23-2001, 01:53 PM

Strange 31 spline axels with c-clip elims, a auburn pro diff, MAC ta girdle. In my opinion this is a real good set up for a street strip car. P.S. I lauch between 5500-6000 rpm.

------------------
92' LX Hatch 5 spd, Performer Intake, 1/2" spacer, pro-m 75mm MAF, 70mm T.B., 24lb injectors, 190lph, BBK fenderwall cold air, mallary ignition & coil, 1.7 rockers, Ripper Shifter, Scattershield, Dual Friction Clutch, SVO Quadrant, Long-Tubes, Off-road H-Pipe, Pro-Dumps, Auburn Pro, 373:1, Strange Axels c-clip elims, control arms, supersubs, 50/50's, Eibach frnt drag springs, Moroso rear trick springs, no sway bar, battery in hatch, 5-Lug Pro-Stars 3 1/2", 8 1/2 26x10.5" MT ET streets, N20

9

moosejaw · 05-23-2001, 02:00 PM

Be sure to get the "street" C-clip eliminators. They are a tapered bearing (take side loading) instead of a ball bearing type (do not take side loading).

Strange has this type and they are rebuildable, if you have a hydraulic press.

Mike

------------------
Live near St.Louis?
Check out Mustang Muscle and Dyno in High Ridge, MO
Check out my ride.

93CobraR · 05-23-2001, 09:15 PM

Theres no comparison to the bullet proof Detriot Locker, hell they run them with 800 hp Nascars, and they never break. They are avalibale for 28,31,33, and 35 spline axles I believe.

------------------
87 GT, 4 inch cowl hood,17x9 Cobra R's/255/45's,GT-40 heads,Crane 2031, Edelbrock intake, long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's.
Best time 12.96
Best MPH 103.42
Best 60' 1.695

Visit my site at:
http://www.geocities.com/cobrar93_2000/MyPage.html

05-21-2001, 10:04 PM	#1
NOSstang89 Registered Member Join Date: Apr 1999 Location: Dallas/College Station, Texas Posts: 143	What rear end parts to buy? The car broke a Moser forged axle last weekend at the track, so I might as well just upgrade the whole rear end so I don't break stuff back there anymore. What stuff will be happy with 5000 rpm launches with 400hp/500tq? I was planning to upgrade to at least 31 spline axles, though I'd prefer 33 or 35. But that depends of what carrier I get... Does anyone make a strong differential that is streetable w/ 33 or 35 splines? If not, will 31's be ok? I also plan to get a rear end girdle kit and some C clip eliminators. I need something that will be pretty good on the street, but strong enough for some hard launches. I also want something that is rebuildable so I don't have to keep buying new units when they wear out (eg., no Auburn or other gear type diffs...). Do such parts exist? Thanks!! ------------------ '92LX hatch, 302 w/TFS Street Heats, Performer RPM intake, Crane cam .499/.510, Crower 1.6rr, 70mmTB/EGR, Pro-M 75mm Maf, SVO 30lb injectors, BBK underdrive pullies, 255lph intank pump, BBK short headers, MAC 2.5" off road X pipe, FMS King Cobra clutch, 3.73 gears, SVO upper arms, HPM Megabite Jr. lowers, Moser forged axles, lakewood driveshaft loop, air pump removed 279.1 rwhp / 303.5 rwtq N/A 395.7 rwhp / 496.5 rwtq NOS

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
What kind of rear end do I have?	Stang_ROTY	Windsor Power	3	01-29-2005 02:46 PM
Rear axle removal question	BLACK85GT	Windsor Power	2	01-06-2003 09:08 PM
Rear Polyurethane Bushings	TMASTER	Windsor Power	4	11-06-2002 11:52 PM
Rear end problems - OUCH!	mysweetlx	Windsor Power	0	09-23-2002 01:40 PM
93 Cobra Rear & Wheels on '89GT	RMARIANI	Windsor Power	0	06-20-2001 06:57 AM

05-21-2001, 11:18 PM	#2
WADS56 gear banger Join Date: Aug 2000 Location: CHICAGO Posts: 1,144	I have moser 31's with a auburn diff. and a girdle. I launch between 5500 and 6000rpm and have had np problems. ------------------ 347 W/ A-trim 6#'s, Canfield heads, out of the box Systemax II intake, solid roller cam. 11.1 @123mph 93lx 5.0 daily driver

05-22-2001, 09:49 AM	#3
LX XLR8R Dirk Diggler Join Date: Feb 1999 Location: SLOATSBURG, NY Posts: 1,931	yea 31 spline mosers, or strange axels with a good diff will be nearly industructable..the powertrax diff is good for 1,000hp if a cheap locker is what ur looking for ------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one.. AIM=onesillynotch

05-23-2001, 01:53 PM	#4
IMPULSERACING Registered Member Join Date: Dec 1999 Location: chicago,IL,USA Posts: 158	Strange 31 spline axels with c-clip elims, a auburn pro diff, MAC ta girdle. In my opinion this is a real good set up for a street strip car. P.S. I lauch between 5500-6000 rpm. ------------------ 92' LX Hatch 5 spd, Performer Intake, 1/2" spacer, pro-m 75mm MAF, 70mm T.B., 24lb injectors, 190lph, BBK fenderwall cold air, mallary ignition & coil, 1.7 rockers, Ripper Shifter, Scattershield, Dual Friction Clutch, SVO Quadrant, Long-Tubes, Off-road H-Pipe, Pro-Dumps, Auburn Pro, 373:1, Strange Axels c-clip elims, control arms, supersubs, 50/50's, Eibach frnt drag springs, Moroso rear trick springs, no sway bar, battery in hatch, 5-Lug Pro-Stars 3 1/2", 8 1/2 26x10.5" MT ET streets, N20 9

05-23-2001, 02:00 PM	#5
moosejaw Registered Member Join Date: Apr 1999 Location: St.Louis,MO Posts: 274	Be sure to get the "street" C-clip eliminators. They are a tapered bearing (take side loading) instead of a ball bearing type (do not take side loading). Strange has this type and they are rebuildable, if you have a hydraulic press. Mike ------------------ Live near St.Louis? Check out Mustang Muscle and Dyno in High Ridge, MO Check out my ride.

05-23-2001, 09:15 PM	#6
93CobraR Registered Member Join Date: Oct 1999 Location: Cincinnati, Ohio Posts: 1,575	Theres no comparison to the bullet proof Detriot Locker, hell they run them with 800 hp Nascars, and they never break. They are avalibale for 28,31,33, and 35 spline axles I believe. ------------------ 87 GT, 4 inch cowl hood,17x9 Cobra R's/255/45's,GT-40 heads,Crane 2031, Edelbrock intake, long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's. Best time 12.96 Best MPH 103.42 Best 60' 1.695 Visit my site at: http://www.geocities.com/cobrar93_2000/MyPage.html