Bogging Under Hard Acceleration

Smokedawg · 06-28-2001, 08:55 AM

I would say that the temp is around 80 degrees. If the throttle body is only 70mm, the MAF is 73, why would I need a bigger MAF if I can only shove so much air through a 70mm hole. I dont want the air to bottleneck on me. I dont know if you can understand what I am saying because it even sounds a little confusing to me trying to read it.

I have had this setup for awhile and it has ran strong before. After it bogged on me trying to pass the other vehicle. I went off onto a country road and tried a few hard launches up through 3 gears and the problem never came back. Its just when I really want the power to get up and move my car, it doesnt want to give it to me.

------------------
347 Stroker Motor: Balanced, Cobra Transmission, Extrude Ported and Polished Upper and ported Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, 30lb Bosch Injectors, Holley AFPR, March Underdrive Pulleys, Perma-Cool Fan, 3-Core Radiator, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 73mm Vortech MAF, 70mm TB, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, AC and Smog del, rear seat del.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Switch to Hybrid Mode Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Backfiring through carb under hard acceleration! ???	yoshi351w	Windsor Power	3	10-19-2003 09:46 PM
strange noise during acceleration	82 GT	Windsor Power	1	11-09-2002 12:50 AM
5.0 spark knock under hard acceleration	johnmcgt	Windsor Power	12	05-19-2002 03:08 PM
Smell under hard acceleration	elma22	Windsor Power	7	09-10-2001 03:39 PM

06-28-2001, 08:55 AM	#3
Smokedawg Tires Fear Me... Join Date: Jan 2001 Posts: 867	I would say that the temp is around 80 degrees. If the throttle body is only 70mm, the MAF is 73, why would I need a bigger MAF if I can only shove so much air through a 70mm hole. I dont want the air to bottleneck on me. I dont know if you can understand what I am saying because it even sounds a little confusing to me trying to read it. I have had this setup for awhile and it has ran strong before. After it bogged on me trying to pass the other vehicle. I went off onto a country road and tried a few hard launches up through 3 gears and the problem never came back. Its just when I really want the power to get up and move my car, it doesnt want to give it to me. ------------------ 347 Stroker Motor: Balanced, Cobra Transmission, Extrude Ported and Polished Upper and ported Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, 30lb Bosch Injectors, Holley AFPR, March Underdrive Pulleys, Perma-Cool Fan, 3-Core Radiator, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 73mm Vortech MAF, 70mm TB, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, AC and Smog del, rear seat del.