Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
01-13-2003, 05:33 PM
|
#1 |
|
Registered Member
Join Date: Dec 2002
Posts: 10
|
Turn Signal Switch on '67
Does anyone know where exactly the turn signal switch is on a '67 Coupe.
According to the Haynes manual I have, its suppose to be on the steering column, passanger side. I can here it clicking, but I can't find it. In addition, is it cylinderical, or square? The replacemant one I have is cylinderical, and the picture shows a cylinderical one; but I was told it may be square. Herkdriver |
|
|
|
01-13-2003, 09:21 PM
|
#2 |
|
Registered Member
Join Date: Nov 2001
Location: Santa Rosa CA
Posts: 35
|
The switch is located under the steering wheel. I replaced the entire switch a while back. Not hard at all. E-mail me with any questions. AJ
|
|
|
|
|
01-14-2003, 10:44 AM
|
#3 | |
|
Registered Member
Join Date: Jan 2003
Location: Arizona
Posts: 6
|
Re: Turn Signal Switch on '67
Quote:
On my 67, the turn signal flasher is behind the dash just above the steering column. Both the turn signal and the 4-way flashers are cylinderical. |
|
|
|
|
|
01-14-2003, 07:15 PM
|
#4 |
|
Registered Member
Join Date: Dec 2002
Posts: 10
|
do you have to remove the dash to get to it?
herkdriver |
|
|
|
|
01-15-2003, 09:14 PM
|
#5 |
|
Registered Member
Join Date: Nov 2000
Posts: 290
|
Are you talking about the switch or flasher? As previously mentioned, the switch is behind the steering wheel which you'll have to remove. The flasher (which is under the dash) can be removed without removing the dash. On my 68, it's basically in the same location behind the dash above the steering column.
|
|
|
|
|
01-15-2003, 09:41 PM
|
#6 |
|
Registered Member
Join Date: Jan 2003
Location: Arizona
Posts: 6
|
If you are talking about the flasher, no you don't have to remove the dash just lay on your back on the floor of the driver's side. It may be tucked up in toward the top of the dash, hard to see and hard to get to but you definately should not have to remove the dash.
|
|
|
|
|
01-15-2003, 09:47 PM
|
#7 |
|
Registered Member
Join Date: Dec 2002
Posts: 10
|
I've tried looking for it, but I can't seem to find it. I can hear though. I'm going to look harder. Thanks for info.
Herkdriver |
|
|
|
|
01-16-2003, 01:28 PM
|
#8 |
|
motors done......woohooo
Join Date: Mar 2002
Posts: 799
|
on my 67 the flasher was mounted on the cluster support right behind the guage cluster, if you take the guage cluster out it should be right there. it is mounted with one of those plastic push in things.
|
|
|
|
|
09-07-2003, 04:35 PM
|
#9 |
|
Registered Member
Join Date: Aug 2003
Posts: 1
|
Turn Signal Switch on '67
One comment, if you are able to hear it, it is apparently
still working. You may be chasing the wrong solution. Also, on my '67, I just had to replace my turn signal flasher, which was NOT reachable without removing the instrument panel. It was tucked up higher than some, perhaps, but since my wasn't working at all anymore, I couldn't use the sound to track it down. While I had it all apart, I took the opportunity to replace the instrument panel bulbs, which makes my dash MUCH easier to see at night.
__________________
Randy Follett |
|
|
|
 |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Question on Hazard / Turn signal flasher (Be prepaired to chuckle @ me) | FritzDaKat | Windsor Power | 3 | 05-26-2003 02:51 AM |
| Replacing 96 Mustang Turn Signal Bulb? | icetime97 | Modular Madness | 0 | 02-10-2003 01:45 PM |
| Turn Signal Flasher | Jacob_M | Blue Oval Lounge | 3 | 09-21-2002 05:52 PM |
| Turn signal blues... | Chris_H | Windsor Power | 6 | 07-25-2002 11:55 AM |
| Dash backlight is out, engine warning and turn signal indicators still work. | bark3rd | Modular Madness | 3 | 06-30-2001 10:03 PM |