408w running poorly

82 GT · 08-30-2005, 08:50 PM

One more thing. I had to re-torque my intake bolts several times before they were seated good.

rwhite65 · 08-30-2005, 09:28 PM

I used the Printo -seal gaskets by Fel pro, FPP-1262 with a 2.100 port height and 1.280 port width. I used the tightening procedure in my haynes maual. I am gonna get a torque wrench tom and retorque them. If that dont work, I am gonna redo them. If I still have a problem, I am gonna suspect the used heads. Thanks guys
Ryan

~The Jester~ · 08-31-2005, 08:50 AM

Quote:

Originally Posted by rwhite65

I used the Printo -seal gaskets by Fel pro, FPP-1262 with a 2.100 port height and 1.280 port width. I used the tightening procedure in my haynes maual. I am gonna get a torque wrench tom and retorque them. If that dont work, I am gonna redo them. If I still have a problem, I am gonna suspect the used heads. Thanks guys
Ryan

Aluminum intakes on Aluminum heads are a pain in the arse. I torgue them (in the correct pattern) starting at 10#, do that like 2 or 4 times until they're ALL at 10#. Once you work your way out to the ends, the middle ones are no longer at 10#, with me? Then up to 15#, do the same thing, then on to 20#, do the same thing, then on to 24#. Be VERY careful on the end bolts!!! There's not alot of meat out on the end of the head for the intake bolt to hang onto. Our 333 is fine, but our 347 I actually had to use longer bolts just on the 4 corners. Sounds like a pain in the ass, and it IS! But that method works really well, and should kill your leak. After the engine gets some heat in her, kill it and retorque. You'll be SURPRISED how loose those bolts are!

rwhite65 · 08-31-2005, 09:20 AM

I would be so happy not have to pull that darn thing again...I still gotta re-pull mine for the trick flow cam I am ordering

thanks guys,
Ryan

~The Jester~ · 08-31-2005, 11:07 AM

Quote:

Originally Posted by rwhite65

I would be so happy not have to pull that darn thing again...I still gotta re-pull mine for the trick flow cam I am ordering

thanks guys,
Ryan

I KNOW what you mean! Bent 2 valves, broke a guide plate, 2 pushrods, 2 rockers up at Fun Ford. Fixed all that over the course of 2 weeks, took the car for a 5 mile test drive, all was well. VERY well! Washed the car, took a shower, heading out to a car show. Car shut off in the driveway. Long story short, the pin came out of the cam gear. Bent 12 valves, 6 pushrods, 1 rocker. Not even 5 miles later, off come the heads.........

Ain't cars FUN???!??!??

Ieatcamaros · 08-31-2005, 12:45 PM

Quote:

Originally Posted by ~The Jester~

I KNOW what you mean! Bent 2 valves, broke a guide plate, 2 pushrods, 2 rockers up at Fun Ford. Fixed all that over the course of 2 weeks, took the car for a 5 mile test drive, all was well. VERY well! Washed the car, took a shower, heading out to a car show. Car shut off in the driveway. Long story short, the pin came out of the cam gear. Bent 12 valves, 6 pushrods, 1 rocker. Not even 5 miles later, off come the heads.........

Ain't cars FUN???!??!??

That sucks!

rwhite65 · 08-31-2005, 03:11 PM

Jester,
Thanks for putting stuff into perspective...now I dont care as much about the leaky intake

Ryan

08-30-2005, 08:50 PM	#1
82 GT Import Slayer Join Date: May 1999 Posts: 2,241	Re: 408w running poorly One more thing. I had to re-torque my intake bolts several times before they were seated good. __________________ '82 GT 351W (.060)Comp Cams 274* Extreme Energy cam, ported & polished heads w/ 1.94/1.60 valves 10.3:1 flat top pistons,stealth intake, Mallory dizzy,Holley 750dp carb, BBK shorties,Flowmaster exhaust,C-4 with 3700 stall converter, B&M pro shifter,8.8 rear, 4:10's, subframes, electric fan, powermaster alternator, 4 core radiator.

08-30-2005, 09:28 PM	#2
rwhite65 Ride Hard Join Date: Oct 2000 Location: Wyoming IL Posts: 1,094	Re: 408w running poorly I used the Printo -seal gaskets by Fel pro, FPP-1262 with a 2.100 port height and 1.280 port width. I used the tightening procedure in my haynes maual. I am gonna get a torque wrench tom and retorque them. If that dont work, I am gonna redo them. If I still have a problem, I am gonna suspect the used heads. Thanks guys Ryan __________________ 65 Fastback 91 roller 306, H/C/I AOD-Bauman, PI Stallion, 4.10's and traction loc 04 Grand Cherokee Freedom Edition 79 Ford F-250 4x4 - Restored

08-31-2005, 09:20 AM	#4
rwhite65 Ride Hard Join Date: Oct 2000 Location: Wyoming IL Posts: 1,094	Re: 408w running poorly I would be so happy not have to pull that darn thing again...I still gotta re-pull mine for the trick flow cam I am ordering thanks guys, Ryan __________________ 65 Fastback 91 roller 306, H/C/I AOD-Bauman, PI Stallion, 4.10's and traction loc 04 Grand Cherokee Freedom Edition 79 Ford F-250 4x4 - Restored

08-31-2005, 03:11 PM	#7
rwhite65 Ride Hard Join Date: Oct 2000 Location: Wyoming IL Posts: 1,094	Re: 408w running poorly Jester, Thanks for putting stuff into perspective...now I dont care as much about the leaky intake Ryan __________________ 65 Fastback 91 roller 306, H/C/I AOD-Bauman, PI Stallion, 4.10's and traction loc 04 Grand Cherokee Freedom Edition 79 Ford F-250 4x4 - Restored

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Car running lean, any suggestions?	MATTKNIGHT	Windsor Power	10	03-08-2009 03:52 PM
My friend is Running WAY lean	TMASTER	Windsor Power	5	07-13-2003 09:41 PM
running rich?	reignman	Windsor Power	2	11-13-2002 10:19 PM
Car's running hot...	Sonics2042	Windsor Power	8	07-16-2002 04:50 PM
If your car is running poorly, get an Autotap!	96SNAKE	Modular Madness	2	11-22-2001 09:50 PM