Holley Systemax intake

Rick 91GT · 10-05-2001, 07:23 AM

Cool, I actually think it will help on motor as well, depending on the cam and heads you have you will be bale to get a little more rpm out of the motor.

Here are my tips and tricks...

DON'T HOOK UP THE PCV TO THE HOLLEY SUPPLIED VACUUM TREE, tap a hole in the intake tube @ 6" from TB and thread a pipe nipple in, run the PCV to that. This will fix the oil pulling issue with the intake, with the PCV hooked up to the intake tree it pulls oil and it will drip out the TB and suck the motor dry..been there done that. I'll send you some pics.

It also made life much easier my making studs instead of using the bolts for the upper. You will need to use a 1262 gasket since the ports on the lower are so damn huge, and if you run the external EGR, use a hex head bolt instaed of the allen bolt that Holley supplies.

You may need a Spacer to clear your adjustable FPR if you run the tree on the backside of the intake (I think it looks better there) You may also need a spacer depending on the valve covers you have. If you run into anything shoot me a e-mail, work rhawver@strouse.com or home Rick91GT@onemain.com.

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon!
<B>12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree

[This message has been edited by Rick 91GT (edited 10-05-2001).]

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Switch to Hybrid Mode Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Trick Flow intake problems	shacar87	Windsor Power	9	11-14-2003 05:53 PM
Holley systemax 2 kit good or bad?	tocchinero	Windsor Power	8	10-22-2003 01:39 AM
Speed Secret # 3	jim_howard_pdx	Windsor Power	13	11-09-2002 10:35 AM
Cobra Intake?	95mustanggt	Windsor Power	5	10-01-2002 09:55 AM

10-05-2001, 07:23 AM	#4
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	Cool, I actually think it will help on motor as well, depending on the cam and heads you have you will be bale to get a little more rpm out of the motor. Here are my tips and tricks... DON'T HOOK UP THE PCV TO THE HOLLEY SUPPLIED VACUUM TREE, tap a hole in the intake tube @ 6" from TB and thread a pipe nipple in, run the PCV to that. This will fix the oil pulling issue with the intake, with the PCV hooked up to the intake tree it pulls oil and it will drip out the TB and suck the motor dry..been there done that. I'll send you some pics. It also made life much easier my making studs instead of using the bolts for the upper. You will need to use a 1262 gasket since the ports on the lower are so damn huge, and if you run the external EGR, use a hex head bolt instaed of the allen bolt that Holley supplies. You may need a Spacer to clear your adjustable FPR if you run the tree on the backside of the intake (I think it looks better there) You may also need a spacer depending on the valve covers you have. If you run into anything shoot me a e-mail, work rhawver@strouse.com or home Rick91GT@onemain.com. ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! <B>12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree [This message has been edited by Rick 91GT (edited 10-05-2001).]