I need help with suspension

Rick 91GT · 01-24-2001, 08:03 AM

I run no front sway bar, 70/30's, 50/50's and the Eibach DRAG launch kit. Lots of transfer, but I don't take corners hard, I really am not into that, that can be seem with my 15 x 3.5 Draglites on the front.

Get the struts and shocks, and if you don't want to buy a good set of uppers, weld plates on your stock uppers to box them in, it helps a lot. I set my pinion angle at 5 degrees which is about the max for a street car anything over 5 degrees should be run at the track only. Don't neglet the torque boxes either, you should weld them up and add a re-enforcement kit. I make a kit that is similar to the BAttle boxes but it has some added support that they don't, they are made from stainless instead of stell so they won't rusyt and they are stronger, e-mail me if your intrested

Rick

------------------
My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Switch to Hybrid Mode Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1991 LX Suspension MODS	Chuck Boone	Windsor Power	2	02-24-2003 08:25 AM
Mustang suspension	Skankin	Corner Carvers Delight	1	08-17-2001 05:10 PM
SUSPENSION, SUSPENSION, SUSPENSION . PLEASE HELP!	BowTie Eater 5 Liter	Windsor Power	11	02-03-2001 07:18 AM
Need Suspension Help!	JohnnyG	Corner Carvers Delight	3	01-15-2001 03:33 PM
Preferred suspension?	Ellis	Corner Carvers Delight	4	08-24-2000 03:57 AM

01-24-2001, 08:03 AM	#6
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	I run no front sway bar, 70/30's, 50/50's and the Eibach DRAG launch kit. Lots of transfer, but I don't take corners hard, I really am not into that, that can be seem with my 15 x 3.5 Draglites on the front. Get the struts and shocks, and if you don't want to buy a good set of uppers, weld plates on your stock uppers to box them in, it helps a lot. I set my pinion angle at 5 degrees which is about the max for a street car anything over 5 degrees should be run at the track only. Don't neglet the torque boxes either, you should weld them up and add a re-enforcement kit. I make a kit that is similar to the BAttle boxes but it has some added support that they don't, they are made from stainless instead of stell so they won't rusyt and they are stronger, e-mail me if your intrested Rick ------------------ My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98