still confused...

Mercury · 11-27-2000, 01:06 AM

I feel your pain. My first car was a buetifull 64 1/2 6cyl coupe. I didnt know anything about cars when I got it.

I was in a horrible accident with it and I started learning alot fast about these cars. It had tons of frame rust, the seller covered all the holes in the front and rear frame rails with bondo and painted over them. Believe it or not, the only good things on the car are the floor pans, and the cowl area. I still have it and hope to restore it about 10 years down the road.

The usual cowl repairs cost on an average of 1600 dollars, the floor pans are alot cheaper depending on what it is you need done and how good you want it done. If your torque box is all ate up it can get costly, but for floor pans you can expect to spend about 450-650 for floor pan repairs.

The second 64 1/2 coupe I bought luckily didnt have any rust on the major parts, just a little bit in the passenger door.

Dont give up on it. If you do, dont scrap the stang. I hate to see a mustang taken to the grave yard and left for dead.

------------------
64 1/2 Red Mustang Coupe. 289, C4, 3:1 rear gear. Mallory duel point. Ported & Polished 65 heads shaved .01 with 351 windsor valves, high side of 10.5:1 comp, 1.7:1 sled rockers, blue wolverine lumpy cam, autolite 4100 Hipo 4 barrel. And to many others to list

2000 Perf Red Mustang GT. 5spd.

64 1/2 red 6cyl coupe. Auto. project car.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Confused, I need help on different fuel pump wiring methods.	5.0 Fiend	Windsor Power	12	10-14-2004 06:43 PM
Yeah, I'm confused	MattwantsSpeed	Windsor Power	4	12-31-2002 01:13 PM
Did oil change and now I'm confused.	stevstum	Windsor Power	6	11-12-2002 11:33 PM
!!!!!!! What size injectors are these? :confused:	bcarter	Windsor Power	24	05-10-2002 06:26 PM
Help Me Please!!! I'm confused	utcreed	Modular Madness	5	12-08-2001 01:04 PM

11-27-2000, 01:06 AM	#1
Mercury The Redneck James Bond Join Date: Sep 2000 Location: Fayetteville NC Posts: 1,707	I feel your pain. My first car was a buetifull 64 1/2 6cyl coupe. I didnt know anything about cars when I got it. I was in a horrible accident with it and I started learning alot fast about these cars. It had tons of frame rust, the seller covered all the holes in the front and rear frame rails with bondo and painted over them. Believe it or not, the only good things on the car are the floor pans, and the cowl area. I still have it and hope to restore it about 10 years down the road. The usual cowl repairs cost on an average of 1600 dollars, the floor pans are alot cheaper depending on what it is you need done and how good you want it done. If your torque box is all ate up it can get costly, but for floor pans you can expect to spend about 450-650 for floor pan repairs. The second 64 1/2 coupe I bought luckily didnt have any rust on the major parts, just a little bit in the passenger door. Dont give up on it. If you do, dont scrap the stang. I hate to see a mustang taken to the grave yard and left for dead. ------------------ 64 1/2 Red Mustang Coupe. 289, C4, 3:1 rear gear. Mallory duel point. Ported & Polished 65 heads shaved .01 with 351 windsor valves, high side of 10.5:1 comp, 1.7:1 sled rockers, blue wolverine lumpy cam, autolite 4100 Hipo 4 barrel. And to many others to list 2000 Perf Red Mustang GT. 5spd. 64 1/2 red 6cyl coupe. Auto. project car.