Project Death Machine??

StangFlyer · 05-16-2001, 01:12 PM

NWell, I am not running a solid roller, I am running a hydraulic roller. It's a custom grind Kam Motion stick, that Ron Robart at Fox Lake Power Products scienced out to match my heads and what I wanted to do. I'll never find the true potential of the engine I have probably, as I can only spin it to 6500 RPM... But, I wanted a low maintenance, sturdy, not going to break it engine. I had enough of that in my push it to the limits 302 days...

Regardless, the cam I have is backwards from what you might think. It is around .600" lift on the intake side with a 1.7 rocker and around .575" lift on the exhaust side. Yes, it has more on the intake than the exhaust. The duration is as expected, however, being around 228 on the intake and 236 on the exhaust. All this is on a 114 lobe. Actually a conservative cam for this big of an engine.

When you're making over 550 HP or so, you will actually make more power by having the intake have more lift than the exhaust. It's backwards from a lower HP engine.

------------------
Dan McClain, Editor
The Mustang Works Magazine
ICQ: 2937586 - AIM: DMcClain91GT
1991 Mustang GT - NOVI Supercharged 377 Stroker
1999 Ford Lightning SVT - 2000 Prototype updated by Roush

[This message has been edited by Dan McClain (edited 05-16-2001).]

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Life	bigwhitecobra	Blue Oval Lounge	41	06-10-2004 10:29 PM
project names!	my9250GT	Blue Oval Lounge	10	06-23-2003 11:56 PM
Answering machine greetings	Mustanguy	Blue Oval Lounge	0	04-12-2003 01:38 AM
Project: Death Machine on Display Thursday (4/18) at Ford HQ	StangFlyer	Blue Oval Lounge	17	04-20-2002 08:08 PM
Hey Dan, What about Project Death Machine?	Coupe Devil	Blue Oval Lounge	5	07-21-2001 02:12 PM

05-16-2001, 01:12 PM	#1
StangFlyer Founder Join Date: Jun 1995 Location: Michigan Posts: 19,326	NWell, I am not running a solid roller, I am running a hydraulic roller. It's a custom grind Kam Motion stick, that Ron Robart at Fox Lake Power Products scienced out to match my heads and what I wanted to do. I'll never find the true potential of the engine I have probably, as I can only spin it to 6500 RPM... But, I wanted a low maintenance, sturdy, not going to break it engine. I had enough of that in my push it to the limits 302 days... Regardless, the cam I have is backwards from what you might think. It is around .600" lift on the intake side with a 1.7 rocker and around .575" lift on the exhaust side. Yes, it has more on the intake than the exhaust. The duration is as expected, however, being around 228 on the intake and 236 on the exhaust. All this is on a 114 lobe. Actually a conservative cam for this big of an engine. When you're making over 550 HP or so, you will actually make more power by having the intake have more lift than the exhaust. It's backwards from a lower HP engine. ------------------ Dan McClain, Editor The Mustang Works Magazine ICQ: 2937586 - AIM: DMcClain91GT 1991 Mustang GT - NOVI Supercharged 377 Stroker 1999 Ford Lightning SVT - 2000 Prototype updated by Roush [This message has been edited by Dan McClain (edited 05-16-2001).]