Balancer: Removing questions???

quick89gt · 02-25-2001, 05:04 PM

My buddy has a '90 lx 5.0, and we are taking the balancer off of it tonight, with the motor still in the car. we were wondering what's the easiest way to keep the damn crank from turning when we do thsi?? put some big screw drivers through the balancer and up under the motor, leave the transmission (5-speed) in gear, what?? Anyone have any advice? we alread have a balancer puller, so that's not a problem...just keeping it from turning will be. thanks, josh

------------------
*************************
'89 GT, T-5,
Bored .030 Over, GT-40P heads, MAC 1 5/8" headers, MAC Off-Road H-Pipe, 2 1/2" Flowmasters, Edelbrock 65mm T.B., Trick Flow Intakes, Crane 2031 cam, 1.7 Roller Rockers, Keith Black hyp. flat top Pistons, Screamin' Deamon Coil, Champion Plugs, March Underdrive Pulleys, 255lph Fuel Pump, SVO Motorsport Clutch, Adjustable Fuel Pressure Regulator, Formula GP Suspension, MAC Upper & Lower Control Arms, FMS 3.73 Gears.
*************************

quick89gt · 02-25-2001, 07:20 PM

anyone???

------------------
*************************
'89 GT, T-5,
Bored .030 Over, GT-40P heads, MAC 1 5/8" headers, MAC Off-Road H-Pipe, 2 1/2" Flowmasters, Edelbrock 65mm T.B., Trick Flow Intakes, Crane 2031 cam, 1.7 Roller Rockers, Keith Black hyp. flat top Pistons, Screamin' Deamon Coil, Champion Plugs, March Underdrive Pulleys, 255lph Fuel Pump, SVO Motorsport Clutch, Adjustable Fuel Pressure Regulator, Formula GP Suspension, MAC Upper & Lower Control Arms, FMS 3.73 Gears.
*************************

boricua_5litro · 02-25-2001, 07:37 PM

Hey guys i just did that this weekend. To loosen the nut i jammed the balancer with a screwdriver. Then i found out about putting the transmission on 1st gear. Make sure that the emergency break is tight. And you have to use a large breaker bar. Good luck.

86GT · 02-25-2001, 07:37 PM

Well if you have an air gun or something, then you won't have a problem getting that bolt out and turning the engine over. Then just use the puller, and it should turn over as your not turning the balancer just that threaded piece against the crank to push the balancer off. Hope that helps...

02-25-2001, 05:04 PM	#1
quick89gt Registered Member Join Date: Apr 2000 Location: O'Fallon, IL Posts: 243	Balancer: Removing questions??? My buddy has a '90 lx 5.0, and we are taking the balancer off of it tonight, with the motor still in the car. we were wondering what's the easiest way to keep the damn crank from turning when we do thsi?? put some big screw drivers through the balancer and up under the motor, leave the transmission (5-speed) in gear, what?? Anyone have any advice? we alread have a balancer puller, so that's not a problem...just keeping it from turning will be. thanks, josh ------------------ *********************** '89 GT, T-5, Bored .030 Over, GT-40P heads, MAC 1 5/8" headers, MAC Off-Road H-Pipe, 2 1/2" Flowmasters, Edelbrock 65mm T.B., Trick Flow Intakes, Crane 2031 cam, 1.7 Roller Rockers, Keith Black hyp. flat top Pistons, Screamin' Deamon Coil, Champion Plugs, March Underdrive Pulleys, 255lph Fuel Pump, SVO Motorsport Clutch, Adjustable Fuel Pressure Regulator, Formula GP Suspension, MAC Upper & Lower Control Arms, FMS 3.73 Gears. ***********************

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
speedy density to mass air questions	thdrcat	Windsor Power	3	09-25-2003 09:20 PM
Balancer questions	GTSteed89	Windsor Power	4	09-02-2003 02:32 PM
Balancer won't budge!!!	chris91LX	Windsor Power	11	01-20-2002 05:58 AM
Harmonic Balancer (part 2)	TJR	Windsor Power	5	09-23-2001 06:09 AM
Harmonic balancer questions	302 LX Eric	Windsor Power	4	03-15-2001 04:57 PM

02-25-2001, 07:20 PM	#2
quick89gt Registered Member Join Date: Apr 2000 Location: O'Fallon, IL Posts: 243	anyone??? ------------------ *********************** '89 GT, T-5, Bored .030 Over, GT-40P heads, MAC 1 5/8" headers, MAC Off-Road H-Pipe, 2 1/2" Flowmasters, Edelbrock 65mm T.B., Trick Flow Intakes, Crane 2031 cam, 1.7 Roller Rockers, Keith Black hyp. flat top Pistons, Screamin' Deamon Coil, Champion Plugs, March Underdrive Pulleys, 255lph Fuel Pump, SVO Motorsport Clutch, Adjustable Fuel Pressure Regulator, Formula GP Suspension, MAC Upper & Lower Control Arms, FMS 3.73 Gears. ***********************

02-25-2001, 07:37 PM	#3
boricua_5litro Registered Member Join Date: Jan 2001 Location: daleville al Posts: 26	Hey guys i just did that this weekend. To loosen the nut i jammed the balancer with a screwdriver. Then i found out about putting the transmission on 1st gear. Make sure that the emergency break is tight. And you have to use a large breaker bar. Good luck.

02-25-2001, 07:37 PM	#4
86GT Sniffed too much n20 Join Date: Oct 1998 Location: Ont, Canada Posts: 1,018	Well if you have an air gun or something, then you won't have a problem getting that bolt out and turning the engine over. Then just use the puller, and it should turn over as your not turning the balancer just that threaded piece against the crank to push the balancer off. Hope that helps...