© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
03-19-2001, 10:06 PM | #1 |
Registered Member
Join Date: Jun 2000
Location: Nor-Cal
Posts: 1,311
|
mid 13's?
I hate asking questions like this, but maybe someone here has some experience similar to this.
Once my suspension stuff is in, Im going to do: 4.10 Gear, Hi flo X-pipe, and Steeda pullies. Now keep in mind Im an auto, and I figure Im running about 14.2 at the lowest right now. Then, 4.10 gear: -.4 X-pipe: -.2 pullies: -.1 = 13.5 Is this just wishful thinking, or do you think I really could hit that with those mods plus what Ive got now? Thanks. ------------------ Black 2000 GT Magnaflow Catback, K&N |
03-19-2001, 10:09 PM | #2 |
Registered Member
Join Date: Jun 2000
Location: Nor-Cal
Posts: 1,311
|
BTW, if you guys have any better ideas for mods, feel free to make suggestions. NO BOOST right now though! Also, around $1000 total.
|
03-20-2001, 08:18 AM | #3 |
Drag Racer!
Join Date: Nov 1999
Location: Lake Worth, FL USA
Posts: 757
|
Pick up a Steeda Timing Adjuster. You'll pick up a good 8-10RWHP. I got 9.2RWHP (dyno proven) with this mod and the timing set to 14*. Plus look at a good set of Drag Radials otherwise you might end up spinning at the line with your new gears.
------------------ 00 GT, MAC Offroad H, Steeda Pulleys, Steeda Timing Adjuster, FMS 4.10’s, Flows w/turndowns, UPR shifter, UPR subframes, UPR LCA’s, Air Filter, Lakewood 70/30 & 50/50, Weld Pro Stars, Nitto DR’s, 253.8RWHP/292.8RWTQ Best on DR's 13.09@103.92 (1.81 60ft) Best on ET Drags 12.99@104.60 (1.67 60ft) M/M 100 88 LX coupe X-FHP, 12pt Cage, UPR K-member, 31 spline rear, full spool… |
03-20-2001, 01:45 PM | #4 |
Registered Member
Join Date: Jun 2000
Location: Nor-Cal
Posts: 1,311
|
Mustang92: I was considering the Timing Adjuster, but I had two questions: If I bump the timing up, do I need to use higher Octane gas? Second, the timing adjuster is pretty noticable in the engine bay, and my car is still deep under warranty. Would the dealer make a big fuss about it?
BTW, your car is rediculous. With just those mods, you must be a great driver. |
03-20-2001, 06:51 PM | #5 |
Registered Member
Join Date: Oct 2000
Location: Saxonburg, PA, USA
Posts: 236
|
Havent done very much at all to mine and have had some very nice and suprising times so far. Time below was with out X-pipe or pulleys. Track opens in 1 1/2 weeks so I wil be chipping more time off.
------------------ 2000 GT Laser red-5speed,MAC Cold Air, MAC 2 1/2" Cat-Back, 3.27gears, Pro-5.0 shifter, Weld Draglite's 15x5 and 15x10, 275/50-15 DragT/A's, 165R15 front Items on car but not run at track yet-BBK offroad X-pipe, BBK Underdrive pullies Best Quarter mile run to date: 13.50@99.97 (1.87 60') |
03-21-2001, 08:34 AM | #6 | |
Drag Racer!
Join Date: Nov 1999
Location: Lake Worth, FL USA
Posts: 757
|
Quote:
As far as my times goes I'm not a great driver but I did spend alot of time at the track learning how to drive it. That makes a world of difference. The car will go 12.8's as it sits but the clutch was slipping, I got a new one in yesterday once I get past the break in I'll have to test it out. [This message has been edited by Mustang92 (edited 03-21-2001).] |
|
Thread Tools | |
Display Modes | Rate This Thread |
|
|