© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
11-23-2001, 06:17 PM | #1 |
Registered Member
Join Date: Oct 1998
Location: Suburban Chicago, Hanover Park
Posts: 695
|
Roller Rocker Weirdness...(Long)
I put in my roller rockers a couple weeks ago and things were fine. Last night I had one of the nuts back out on me and I pulled it apart and re-torqued all of them again. The problem is that I noticed after I hand tightened the nuts down on the rockers, on cylinders 5,6,7,8 both rockers (intake and exhaust) would tighten easily with the wrench, compressing the valves and valve springs at least a half an inch. The weird part was that in cylinders 1,2 & 3 after the nut was tightened hand-tight, the wrench would barley tighten the nut more than a 1/4 turn and it was TIGHT. It just seems odd that 10 of the sixteen valve/valve springs would compress so much while the others didn't compress at all. A freind thought the valve springs may be tired but it seemes awful uniform for all of them except the ones in cylinders 1,2 & 3 to be bad. Anyone have any ideas why this would be? TIA
__________________
My Ford Club http://www.midwestfords.org/ Best time N/A 12.9 @ 107 1.711 60' 125 shot - 12.04 @ 113 1.59 60' |
11-23-2001, 06:50 PM | #2 |
Registered Member
Join Date: Oct 1998
Location: Suburban Chicago, Hanover Park
Posts: 695
|
Oh yeah, I DID adjust them when the lifters were on the flat part of the cam lobe. I ended up tigtening them by hand then snugging them down about a half turn with the wrench and tightening the crap out of the set screw.
|
11-24-2001, 07:27 AM | #3 |
Registered Member
Join Date: Oct 2001
Location: orlando,fl USA
Posts: 44
|
Rocker Arm adjustment
If you get a Chiltons book(the professional one,check out public library,and make copys)I have done the valve adjustment a few times with good resuilts.If you were tightening down the spring,
you may need to shim rocker arm or get shorter push rod.
__________________
89'LX 5.oh.BBK shortys,no cats Flow masters w/Dumps,Crane Cam(Top secert) MSD 6AL,Blaster coil,Motor sport 9mm wires,under drive pulleys,no smog timming @ 16 deg,K&N,70 mm maf, Pro5.0shifter,Home made frame con. south side lift bars,3.73 bald @#! tires(2 on rear!)Sony C-D and Rockford fasgate rear,w/sony explode 5 1/2 in front. |
11-24-2001, 10:03 AM | #4 |
dude5l
Join Date: May 2001
Location: Grande Prairie, Alberta, Canada
Posts: 603
|
Hi Chris,
that does sound quite odd. I believe that your cylinders 5,6,7,8 are normal and you have a problem with the other bank of cylinders. (#4 as well? )Was the motor rebuilt in the last little while? I'm just asking because a similar thing happened to me a long time ago and it had turned out one bank of pistons (domed ) was installed backwards. It sounds as if you definitly have an interference problem somewhere.
__________________
Good luck! Brad R. 1992 L.X. 5.0 coupe MODS: A few little bolt ons New Best time ...11.60 @ 128 mph @ 2000+ ft altitude. Rice Haters Club member #39 Users rides #2542 |
11-24-2001, 10:26 AM | #5 |
Registered Member
Join Date: May 1999
Location: SAN ANTONIO, TEXAS, USA
Posts: 611
|
I had the SAME problem
I am still not sure what exactly fixed it, but I do remember replacing my valve springs, and lifters not too long afterwards.
I do think it is just that that bank had mostly compressed lifters, if U were to take the lifters out and soak them in oil overnight, and try adjusting them U will not see that again (at least for that time) I don't think it is necesary for that though. Just adjust it the right way (all I did) and it should be fine. I would suggest replacing your lifters if they are still stock or over 50-60g miles (cheap enough insurance).
__________________
Black SN95 TFS heads, Holley intake, AFM B-2 cam, 12.9 @110mph best ET 13.06 @111mph best MPH After gutting out clogged cats and a much better tune. Took Nitrous out for warranty work didn't have time to put back in for track. |
11-24-2001, 07:39 PM | #6 |
Registered Member
Join Date: Oct 1998
Location: Suburban Chicago, Hanover Park
Posts: 695
|
The engine is bone stock with 75000 miles. The first time the valve covers were off was when I put the rockers on a couple weeks ago. The pushrods were brand new Ford Racing Hardened ones I put in with the rockers, same length as stock. Thought it might have been the lifters frozen all the way up, but I couldn't get them to go down by pushing down on the pushrod. It just seemed odd that both valves on 5 cylinders were one way and both valves on the other three were another. I'm planning on getting heads in the next few weeks anyway so I'm not too concerned, just curious. Thanks for the replys, maybe I'll never know for sure.
|
Thread Tools | |
Display Modes | Rate This Thread |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Angus Racing Roller Rocker | QuantumMotorsports | Windsor Power | 5 | 10-10-2009 05:59 PM |
Roller rocker question? | HiFlow5 0 | Windsor Power | 1 | 05-18-2004 12:07 PM |
Adjustable roller rocker problems | Greystang302 | Windsor Power | 0 | 05-14-2001 01:57 PM |
Roller Rocker install questions. (long) | chris91LX | Windsor Power | 5 | 03-15-2001 09:32 PM |
Valve cover / roller rocker interference | gray87GT | Windsor Power | 1 | 01-06-2001 01:43 PM |